ACS USB Installation Boot maker

This directory contains utilies and images files, can used to

Create media capable of installing Cisco ACS.

The iso-to-usb.sh script would create a bootable USB key with the

ACS ISO image. The usage is as follows:

iso-to-usb.sh Source_iso Usb_device

For example, if your USB device WAS/DEV/SDC, and your source ISO

Image is Acs-5.4.0.40-2242--08-29-2012.iso, you would use this syntax:

#./iso-to-usb.sh ACS-5.4.0.40-2242--08-29-2012.ISO/DEV/SDC

The iso-to-usb.sh script requires a functioning Linux installation to run.

It has been tested under Rhel 5, Rhel 6, CentOS 5.x, CentOS 6.x.

Note that after running ' iso-to-usb.sh ', your USB key would be

Partitioned in a format where non-linux operating systems would not

Recognize all of the space available. To repurpose your USB

Key for general purpose use with Windows or MACOS, run the

'repurpose-usb.sh' utility in the This directory. This utility

Would repartition and reformat your USB key for general use.

Operation: ======VM ===== access u disk ========

[Email protected] aping># fdisk-l

disk/dev/sda:21.5 GB, 21474836480 bytes

255 heads, Sectors/track, 2610 cylinders

Units = Cylinders of 16065 * 8225280 bytes

Sector size (logical/physical): bytes/512 bytes

I/O size (minimum/optimal): bytes/512 bytes

Disk identifier:0x000e4e87

Device Boot Start End Blocks Id System

/DEV/SDA1 * 1 2356 18922496 Linux

/dev/sda2 2356 2611 2048000, Linux Swap/solaris

disk/dev/sdb:15.8 GB, 15829303296 bytes

Heads, Wuyi sectors/track, 5051 cylinders

Units = Cylinders of 6120 * 3133440 bytes

Sector size (logical/physical): bytes/512 bytes

I/O size (minimum/optimal): bytes/512 bytes

Disk identifier:0x21be21bd

Device Boot Start End Blocks Id System

/DEV/SDB1 * 221 5052 14784640 c W95 FAT32 (LBA)

Re-partition formatting.

[Email protected] aping># MKFS.EXT3/DEV/SDB1

MKE2FS 1.41.12 (17-may-2010)

File System label =

Operating system: Linux

Block size =4096 (log=2)

Chunked size =4096 (log=2)

Stride=0 blocks, Stripe width=0 blocks

966656 inodes, 3864008 blocks

193200 blocks (5.00%) reserved for the Super user

First block of data =0

Maximum filesystem blocks=3959422976

118 block Groups

32768 blocks per group, 32768 fragments per group

8192 inodes per group

Superblock backups stored on blocks:

32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208

Writing Inode table: complete

Creating Journal (32768 blocks): complete

/DEV/SDB1 1 5051 15456034+ Linux

[Email protected] aping>#/iso-to-usb.sh Acs_v5.5.0.46.iso/dev/sdb

Error:missing dependency: syslinux here is missing a dependency package

Please install the package with Syslinux and try again

[Email protected] aping># RPM-IVH syslinux-3.11-7.i386.rpm

Warning:syslinux-3.11-7.i386.rpm:header V3 dsa/sha1 Signature, key ID E8562897:nokey

error:failed dependencies:

Mtools is needed by syslinux-3.11-7.i386

[email protected] aping># LL

Total dosage 1870848

-rw-r--r--1 aping aping 1915023360 June acs_v5.5.0.46.iso missing packages can be found in this image, ACS based on Linux system development

-rwxr-xr-x 1 aping aping 11873 November iso-to-usb.sh

-rw-r--r--1 aping aping 213717 November mtools-3.9.10-2.fc6.i386.rpm

-rw-r--r--1 aping aping 982 November

-rw-r--r--1 aping aping 486126 February syslinux-3.11-7.i386.rpm

[Email protected] aping># RPM-IVH mtools-3.9.10-2.fc6.i386.rpm

Warning:mtools-3.9.10-2.fc6.i386.rpm:header V3 dsa/sha1 Signature, key ID E8562897:nokey

Preparing ... ########################################### [100%]

1:mtools ########################################### [100%]

[Email protected] aping># RPM-IVH syslinux-3.11-7.i386.rpm

Warning:syslinux-3.11-7.i386.rpm:header V3 dsa/sha1 Signature, key ID E8562897:nokey

Preparing ... ########################################### [100%]

1:syslinux ########################################### [100%]

[Email protected] aping>#

[Email protected] aping>#/iso-to-usb.sh ACS_V5.5.0.46.ISO/DEV/SDB1

Error:device must be raw USB Device such as/dev/sdb OR/DEV/SDC

Perhaps like you gave a parition name, such as/dev/sdb1

[Email protected] aping># /iso-to-usb.sh acs_v5.5.0.46.iso/dev/sdb

W A R n I N G * * *

This SCRIPT would DELETE all EXISTING CONTENT on YOUR USB Drive:/dev/sdb

Is you sure want to CONTINUE? [y/n]: Y

Deleting partition table on USB drive:/dev/sdb ...

Creating new partition table on USB drive:/dev/sdb ...

formating BOOT partition:/DEV/SDB1 as VFAT ...

formating DATA partition:/dev/sdb2 as EXT2 ...

Copying syslinux files to USB partition:/dev/sdb1 ...

Copying ISO file to USB partition:/dev/sdb2 ...

done!

This completes the production of USB

In addition, it can be burned into a disc to install.

Soft Disc Pass UltraISO

This article is from the "673879223" blog, please be sure to keep this source http://miller0intarnet.blog.51cto.com/1550653/1793773

ACS USB installation boot maker