ADSL dialing error code details

ADSL dialing error code details

Error 602 the port is already open
Problem: the dial-up network cannot be connected due to a device installation error or in use.
Cause: raspppoe is not fully and correctly installed.
Solution: uninstall and reinstall any pppoe software.

Error 605 cannot set port information
Problem: the port cannot be set for the dial-up network due to device installation errors
Cause: raspppoe is not fully and correctly installed.
Solution: uninstall and reinstall any pppoe software.

Error 606 the port is not connected
Problem: the dial-up network cannot connect to the required device Port
Cause: raspppoe is not completely and correctly installed. connection line faults and ADSL modem faults
Solution: Uninstall any pppoe software, reinstall it, and check the network cable and ADSL modem.

Error 608 the device does not exist
Problem: the device connected to the dial-up network does not exist.
Cause: raspppoe is not fully and correctly installed.
Solution: uninstall and reinstall any pppoe software.

Error 609 the device type does not exist
Problem: the type of the device connected to the dial-up network cannot be determined.
Cause: raspppoe is not fully and correctly installed.
Solution: uninstall and reinstall any pppoe software.

Error 611 the route is not available/612 the route is not allocated
Problem: the dial-up network connection route is incorrect.
Cause: the raspppoe is not fully and correctly installed, and the ISP Server is faulty.
Solution: uninstall and reinstall any pppoe software.

Error 617 the port or device is already Disconnecting
Problem: the device connected to the dial-up network has been disconnected.
Cause: raspppoe is not completely and correctly installed. ISP Server faults, connection lines, and ADSL modem faults
Solution: Uninstall any pppoe software, reinstall it, and check the network cable and ADSL modem.

Error 619 problem: unable to establish a connection with the ISP Server
Cause: adsl isp Server fault and ADSL Telephone Line Fault
Solution: Check whether the ADSL signal lights are correctly synchronized.

621 cannot open the phone book file
622 cannot load the Phone Book File
Error 623 cannot find the phone book entry
Error 624 cannot write the Phone Book File
Error 625 invalid information found in the phone book
Problem: Windows NT or Windows 2000 server network Ras network component failure
Cause: Uninstall all pppoe software and reinstall the RAS network component and raspppoe.

Error 629: the connection has been disconnected from the peer computer. Double-click the connection and try again.
If this problem occurs, the situation is complicated, because there are many situations that can lead to "error 629", most of which is caused by too many people simultaneously dial in. In addition, you should set all the default settings in your dial-up connection settings, such as "enable software compression" and "log on to the network. Generally, this situation may also be caused by the performance and quality of the modem or telephone line you use, so that the connection cannot be established well at the selected communication rate, another scenario is: if your phone has enabled the anti-theft function, there will be a handshake sound from the modem during dialing, but error 629 will occur after shaking the audio, if an extension calls the phone, an alarm is triggered. You only need to disable the anti-theft function.

Error 630
Problem: no response from ADSL Modem
Cause: ADSL telephone line fault, ADSL modem fault (power supply not open, etc)
Solution: Check the ADSL device.

Error 633
Problem: the dial-up network cannot be connected due to a device installation error or in use.
Cause: raspppoe is not fully and correctly installed.
Solution: uninstall and reinstall any pppoe software.

Error 638
Problem: after a long time, you cannot connect to the ISP's ADSL Access Server
Cause: the ISP Server is faulty. You entered a wrong phone number in the poor connection created by raspppoe.
Solution: Run raspppoe.exe with the created Dial to check whether the ISP service can be listed to ensure that the ISP is normal. Clear the phone number in the used dial-up connection or retain only one 0.

Error 645
Problem: The NIC does not respond correctly
Cause: Nic fault or NIC Driver fault
Solution: Check the NIC and reinstall the NIC Driver.

Error 650
Problem: the remote computer does not respond and the connection is disconnected.
Cause: Network Protocol Error Caused by adsl isp Server fault, Nic fault, abnormal Shutdown
Solution: Check whether the ADSL signal lights are correctly synchronized. Check the network adapter and delete all network components to reinstall the network.

Error 651
Problem: Error reported by ADSL Modem
Cause: Windows is in safe mode, or other errors
Solution: When this error occurs, repeat it to report the specific error code.

Error 676, busy. Please try again later.
Check whether there is a problem with the telephone line. Unplug the telephone line and connect it directly to the phone. Call the ISP phone number (such as 163,169) to be dialed by phone ), if there is a scream like a fax sound in the receiver, it means that you can dial up the Internet, make sure that the phone number in "My Computer"-> "Dial-Up Network"-> "XXX connection (your dial-up connection)" has no other numbers before the ISP phone number, if you are dialing through an extension, you need to add an external line number and a comma before the phone number, such as "0,163 ". If it is a busy line sound in the receiver, and the busy frequency is extremely high.

Error 678. The caller's computer did not respond.
This situation is similar to the busy line, Mostly accidental. Sometimes it is caused by dialing when the modem is just started. Please confirm the telephone line first (the one connected to the telephone Board) insert the line interface of the modem. Check whether there is a problem with the telephone line. Unplug the telephone line and connect it directly to the phone. Call the ISP phone number (such as 163,169) to hear whether there is a scream similar to a fax in the receiver, if so, your phone number can be used for dial-up Internet access. Please confirm "my computer"-> "Dial-Up Network"-> "XXX connection (your dial-up connection) "The phone number in does not have any other number before the ISP phone number. If you dial through the switchboard, you must add an external phone number and a comma before the phone number, such as" 0,163 ". If the voice is busy, contact the ISP customer service department. If you have no voice or prompt that you cannot call this phone number, it indicates that your telephone line is faulty.

Error 680: no dial tone.
If this error occurs, check whether the modem is correctly connected to the telephone line and then check the following aspects:
1. Check whether the telephone line is connected. If no problem is found, unplug the telephone line and connect it directly to the phone. Call the ISP phone number (such as 163,169 ), if you hear a scream like a fax sound in your phone, it means that you can dial up the Internet. It may be that you have called in when you dial up, or your modem has a fault. If the voice is busy, contact the ISP customer service department. If you have no voice or prompt that you cannot call this phone number, it indicates that your telephone line is faulty.

Error 691
Problem: the user name and password entered are incorrect. A connection cannot be established.
Cause: the user name and password are incorrect, and the ISP Server is faulty.
Solution: use the correct username and password, and use the correct ISP account format (name @ service ).

Error 718
Problem: no response is returned when the remote computer times out when the user name is verified. The connection is closed.
Cause: adsl isp Server fault
Solution: Call 2022370.

Error 720
Problem: the dial-up network cannot coordinate server protocol settings in the Network
Cause: the adsl isp Server is faulty. An abnormal shutdown may cause a network protocol error.
Solution: delete all network components and reinstall the network.

Error 734
Problem: the PPP Connection Control Protocol is suspended.
Cause: the adsl isp Server is faulty. An abnormal shutdown may cause a network protocol error.
Solution: delete all network components and reinstall the network.

Error 738
Problem: the server cannot assign an IP address
Cause: the adsl isp Server is faulty. Too many ADSL users exceed the IP addresses that the ISP can provide.
Solution: Call 2022370.

Error 797
Problem: The ADSL Modem connection device is not found
Cause: the power supply of the ADSL modem is not enabled, and the connection line between the nic and the adsl modem is faulty. After the software is installed, the corresponding protocol is not properly set. When a dial-up connection is created, an incorrect null connection is established.
Solution: Check the power supply and connection lines, check the network properties, and check whether the raspppoe-related protocols are correctly installed and properly bound (related Protocols), and check whether the NIC appears? No. Or! Check whether the connected device uses a device named "ISDN channel-adapter name (XX, this device is an empty device. If you cancel it, select the correct pppoe device to replace it, or re-create a dial-up connection.

 

------------------------------------- Very handsome split line ------------------------------------------------------------

------------------------------------- Very handsome split line ------------------------------------------------------------

 

600 the operation is suspended.

601 an invalid PORT handle is detected.

602 the specified port is enabled.

603 the caller's buffer zone is too small.

604 incorrect information is specified.

605 port information cannot be set.

606 the specified port is not connected

607 invalid events are detected.

608 the specified device does not exist.

609 the specified device type does not exist.

610 the specified buffer is invalid.

611 the specified route is unavailable.

612 the specified route is not allocated.

613 the specified compression is invalid.

614 there is not enough buffer available.

615 the specified port is not found.

616 the asynchronous request is suspended.

617 the modem is disconnected.

618 the specified port is not opened.

619 the specified port is not connected. [Color = Red] ISP Server fault or device line fault [/color]

620 the endpoint cannot be determined.

621 the system cannot open the phone book.

622 the system cannot load the phone book.

623 the system cannot find the phone book for this connection.

624 the system cannot update the phone book file.

625 the system found invalid information in the phone book.

626 the string cannot be loaded.

627 the keyword cannot be found.

628 the connection is closed.

629 the connection is disabled by the remote computer. [Color = Red] Why is the server re-connecting or calling I telecom service provider after a while [/color]

630 the modem is disconnected due to hardware failure. [Color = Red] Try to reset the ADSL device. [/color]

631 the user disconnects the modem.

632 incorrect structure size detected.

633 the modem is in use or is not configured as a dial-out.

634 your computer cannot be registered on a remote network

635 an unknown error occurs.

636 The device connected to the port is not the expected device.

637 the unconvertible string is detected.

638 request timeout. [Color = Red] This error occurs when a wide-area broadband obstacle occurs. (If n-plus broadband users log on to the server at the same time, the server cannot allocate an IP address. [/color]

639 Asynchronous Network is unavailable.

640 NetBIOS-related errors.

641 the server cannot allocate NetBIOS resources required to support the client.

642 a NetBIOS Name of a computer has been registered on a remote network.

643 the NIC on the server is faulty.

644 you will not be able to receive network pop-up messages.

645 internal authentication error.

646 this account cannot be logged on at this time.

647 this account is disabled.

648 the password of this account has expired.

649 the account does not have the permission to dial in.

650 the remote access server does not respond.

651 the modem reports an error.

652 there is an unrecognized response from the modem.

653 The macro requested by the modem is not found in the device. inf file.

654 commands or responses in the device. inf file reference undefined macros.

655 The <message> macro is not found in the device. inf file.

656 the <defaultoff> macro in the device. inf file contains an undefined macro.

657 unable to open the device. inf file.

658 the device name in the device. inf or media. ini file is too long.

659 the media. ini file references an unknown device name.

660 the device. inf file does not contain responses to commands.

661 the command is missing from the device. inf file.

662 try to set macros not listed in the device. inf file section.

663 the media. ini file references an unknown device type.

664 the system memory is insufficient.

665 the modem is incorrectly configured.

666 the modem is not working properly.

667 the system cannot read the media. ini file.

668 the connection is terminated.

669 the usage parameter in the media. ini file is invalid.

670 the system cannot read some names from the media. ini file.

671 the system cannot read the device type from the media. ini file.

672 the system cannot read the device name from the media. ini file.

673 the system cannot read the usage from the media. ini file.

674 The system cannot read the maximum connection rate (BPS) from the media. ini file ).

675 the system cannot read the maximum carrier connection speed from the media. ini file.

676 telephone lines are busy.

677 is answered by a person rather than a modem.

678 no response. [Color = Red] If the ADSL device is fully on (except for data) and is always on, turn off the device for 5-10 minutes and start the connection. If the link light is flashing, it is recommended to submit a ticket to the telecommunications department for repair [/color]

679 the system cannot detect the carrier.

680 no dialing sound.

681 the modem reports a general error.

691 access is denied because the user name and/or password are invalid in this domain. [Color = Red] incorrect user name and password, broadband account binding error, or account status error. It may also be because the account is not properly deprecated and cannot be logged on to the Internet. [/color]

692 the modem has a hardware fault.

695 the machine is not started.

696 started machines.

697 the response cycle is incomplete.

699 the modem's response causes a buffer overflow.

700 the extension command in the device. inf file is too long.

701 the modem uses a connection speed not supported by the COM driver.

703 the connection requires user information, but the application does not allow user interaction.

704 the callback number is invalid.

705 the authentication status is invalid.

707 errors related to the X.25 protocol.

708 The account has expired.

709 An error occurred while changing the password in the domain. The password may be too short or match with the previous password. The password may be too short or may match the previous password.

710 serial overflow error detected when communicating with the modem.

711 Remote Access Service Manager cannot start the event log to provide other information.

The 712 dual port is being initialized. Wait a few seconds before redial.

713 no active ISDN line is available.

714 no ISDN channel is available for dialing.

715 too many errors have occurred due to poor telephone line quality.

716 Remote Access Service IP Address Configuration is unavailable.

717 no IP address is available in the static pool for remote access to the service IP address.

718 connection timeout waiting for the remote computer to respond effectively.

719 the connection is terminated by the remote computer.

720 the connection attempt fails because your computer and the remote computer have different PPP control protocols. [Color = Red] reinstalling the system or TCP/IP Protocol [/color]

721 the remote computer did not respond.

722 receive invalid data from the remote computer. The data is ignored.

723 the telephone number (including the prefix and suffix) is too long.

726 IPX protocol cannot be used to simultaneously dial out on multiple modems.

728 the system cannot find the IP adapter.

729 slip cannot be used unless the IP protocol is installed.

731 no protocol is configured.

732 the PPP control protocol for your computer and remote computer cannot be consistent.

733 the PPP control protocol for your computer and remote computer cannot be consistent.

734 the PPP Connection Control Protocol is terminated. [Color = Red] If you have an ISP Server problem, call the local telecommunications department for consultation. [/color]

735 the request address is rejected by the server.

736 the remote computer terminated the control protocol.

737 the loop is detected.

738 no IP address is assigned to the server.

739 the authentication protocol required by the remote server cannot use the Stored Password. Redial and enter the password explicitly.

740 invalid dialing rule detected.

741 the local computer does not support the required data encryption type.

742 remote computers do not support the required data encryption types.

743 data encryption is required for remote servers. [Color = Red] Server Authentication fails [/color]

751 the callback number contains invalid characters. Only the following characters are allowed: 0 to 9, T, P, W, (,),-, @, and space.

752 syntax errors occur when processing scripts.

753 the connection cannot be disconnected because it is created by a multi-protocol router.

754 The system cannot find the multi-link binding.

755 because the User-Defined dialing program has been specified for this item, the system cannot perform automatic dialing.

756 you have already called this connection.

757 the remote access service cannot be started automatically. Other information is provided in the event log.

758 Internet Connection Sharing is enabled on the connection.

760 An error occurred while enabling the routing function.

761 An error occurred while enabling Internet Connection Sharing.

763 cannot start Internet Connection Sharing. In addition to shared connections, there are two or more LAN connections.

764 no smart card reader is installed.

765 cannot start Internet Connection Sharing. You have configured the IP address required to automatically enter the IP address for the LAN connection.

766 the system cannot find any certificate.

767 cannot start Internet Connection Sharing. Multiple IP addresses are configured for the LAN connection selected on the VPC. Before enabling Internet Connection Sharing, use a single IP address to reconfigure the LAN connection.

768 connection attempts failed due to data encryption failure.

769 the specified destination is inaccessible. [Color = Red] Check the NIC [/color]

770 remote machines reject connection attempts.

771 connection attempt failed because the network is busy.

772 the network hardware of the remote computer is incompatible with the requested telephone type.

773 the connection attempt fails because the target number has been changed.

774 temporary failure causes connection failure. Try again.

775 the call is blocked by a remote computer.

776 because the target has already called the "Do Not Disturb" function, the call cannot be connected.

777 the modem on the remote computer fails and the connection attempt fails.

778 the server identity cannot be verified.

779 use this connection to dial out. You must use a smart card.

780 the function used is invalid for this connection.

781 failed the encryption attempt because the valid certificate cannot be found.

782 Network Address Translation (NAT) is currently installed as a routing protocol and must be deleted before Internet Connection Sharing is enabled.

783 Internet Connection Sharing cannot be enabled. The LAN connection selected as the private network is not currently connected or is disconnected from the network. Make sure that you have connected to the LAN adapter before enabling Internet Connection Sharing.

784 when logging on, you cannot use this connection for dialing because it is configured with a different user name than the one on the smart card. To use it during login, you must configure it to use the user name on the smart card.

785 when logging on, you cannot use this connection for dialing because it is not configured as a smart card. To use it during login, you must edit the properties of the connection to use the smart card.

786 L2TP connection attempt failed because there is no valid computer certificate on the computer during security verification.

787 L2TP connection attempt failed because the security layer cannot verify the remote computer.

788 L2TP connection attempt failed because the security layer cannot negotiate with the remote computer for compatibility parameters.

789 L2TP connection attempt failed because the security layer encountered a processing error during initial negotiation with the remote computer.

790 L2TP connection attempt failed because certificate verification on the remote computer failed.

791 L2TP connection attempt failed because the security policy for the connection was not found.

792 L2TP connection attempt failed because security negotiation times out.

793 L2TP connection attempt failed due to security negotiation error.

794 the radius attribute of the user's frame protocol is not PPP.

795 the radius attribute of the user's tunneling type is incorrect.

796 the radius attribute of the user's service type is neither frame nor frame callback.

797 the connection to the remote computer cannot be established because the modem cannot be found or the modem is busy. [Color = Red] The power supply of the ADSL device is not on [/color]

798 the certificate that can be used with the Scalable Authentication Protocol cannot be found.

799 Internet Connection Sharing (ICS) cannot be enabled because an IP address conflict exists on the network ). ICS requires that the host be configured to use 192.168.0.1. Make sure that no other customer on the network is configured to use 192.168.0.1.

800 unable to establish a VPN connection. The VPN Server cannot be connected, or the security parameter configuration of the connection is incorrect.