Build Cisco SDM Management Interface

Cisco Security Device Manager (SDM) is a very special part. We can set many functional parameters for the router device through the graphical interface.

Here I will describe how to install and display the SDM Management Interface in detail. The vro here is made using Dynamips software. The following are detailed steps for installation and testing:

Step 1: Add a Microsoft Loopback Adapter Nic. Select <add hardware> in <Control Panel>, and click Next. Select <yes, I have connected to this hardware> when the following page appears.

650) this. width = 650; "onclick = 'window. open (" http://blog.51cto.com/viewpic.php? Refimg = "+ this. src) 'style = "width: 578px; height: 249px" height = "309" alt = "" src = "http://www.bkjia.com/uploads/allimg/131227/034G24616-0.gif" width = "578" border = "0"/>

650) this. width = 650; "onclick = 'window. open (" http://blog.51cto.com/viewpic.php? Refimg = "+ this. src) 'height =" 307 "alt =" "src =" http://www.bkjia.com/uploads/allimg/131227/034G24538-1.gif "width =" 570 "border =" 0 "/>

 

Select the second item when the page appears. Then select the Microsoft Loopback Adapter Nic In the network Adapter.

650) this. width = 650; "onclick = 'window. open (" http://blog.51cto.com/viewpic.php? Refimg = "+ this. src) 'alt =" "src =" http://www.bkjia.com/uploads/allimg/131227/034G23342-2.gif "border =" 0 "/>

After the NIC is installed, You need to configure the IP address and subnet mask for it. The IP address here is configured as a private IP address, as shown in figure 10.10.10 . 10 ).

Step 2: Install the Win_pcap.cmd (windows NT Command Script) component. Note: If the shipping line is not running properly, we cannot complete communication between the local host and the simulation router. The following interface appears, and then the NIC parameters marked to paste the MS LoopBack.

 

650) this. width = 650; "onclick = 'window. open (" http://blog.51cto.com/viewpic.php? Refimg = "+ this. src) 'height =" 266 "alt =" "src =" http://www.bkjia.com/uploads/allimg/131227/034G2N92-3.gif "width =" 581 "border =" 0 "/>

 

Step 4: run a JAVA Plug-in.

Step 5: run the virtual service. batMS-DOS batch file), and then run the SDM. cmd program in two windows at the same time ). Note that the order in which the two windows are opened is different, so that we cannot display the relevant parameters for the desired outlets. Run the list command on the following interface and then run the start R1 command (to activate router R1, case sensitive ). And then remotely connect to the router R1 switch ). Then we will enter the same configuration interface as our common vro.

 

 

 

Step 6: after entering the vro, we need to set the vro. 1. Configure the IP address and subnet mask for the Fast Ethernet port. The IP address here is configured 10.10.10 . 11 this must be in the same network as the IP address configured on the host ). 2. Enable the HTTP/HTTPs service in global mode. Run the following commands: ip http server and ip http secure-server. Finally, enter the command ip http authentication local for local verification. 3. Set username, priority pribilege), and password, for example, command username cisco privilege 15 passsword 123 (15 indicates the highest priority ). 4. Configure the console, SSH, and Telnet. You only need to perform local verification on the console and Vty by using the command login local .. Finally, you need to set the transmission mode to Telnet and use the SSH protocol. In this way, the configuration is complete, and then save the settings.

Step 7: Install the sdm.exe file. This operation is simple. After installation, the following interface is displayed:

Enter the IP address of the configured vro, and then click <Start>.

 

650) this. width = 650; "onclick = 'window. open (" http://blog.51cto.com/viewpic.php? Refimg = "+ this. src) 'style = "width: 524px; height: 247px" height = "159" alt = "" src = "http://www.bkjia.com/uploads/allimg/131227/034G2JD-4.jpg" width = "524" border = "0"/>

A web page is displayed, and a small window is displayed. You need to enter the user and password you Just configured.

 

650) this. width = 650; "onclick = 'window. open (" http://blog.51cto.com/viewpic.php? Refimg = "+ this. src) 'alt =" "src =" http://www.bkjia.com/uploads/allimg/131227/034G2O52-5.gif "border =" 0 "/>

A page similar to the following page does not display the following information in detail), and another small window may require you to reset a user and password, the following interface is displayed, which is the final graphic operation interface of SDM. Here you can perform a series of settings on the vro. The sdm of the vswitch is the same operation method. Here we will not elaborate on the appearance of the SDM interface of the vswitch.

 

650) this. width = 650; "onclick = 'window. open (" http://blog.51cto.com/viewpic.php? Refimg = "+ this. src) 'alt =" "src =" http://www.bkjia.com/uploads/allimg/131227/034G22427-6.gif "border =" 0 "/>

At last, you must note that the following web pages may not be opened due to browser problems. In this case, you need to modify an option for IE. The specific modification process is as follows:

Open IE browser -- select <tools> -- select <Internet Options...> -- select <advanced> -- select <allow active content to run in files on my computer>. By default, IE is not selected.

As the SDM management interface, it will be involved in the CCNA examination. Here is just some of my operations, hoping to help you with your learning.

 

This article is from the "Technology for the Future" blog. For more information, contact the author!