In addition to better singing skills, post-production is also an essential step. I will share some of my experiences in production with you, I hope you will continue to study and discuss your work in depth and make your work better! I. Current sound:
Do not use a microphone to enhance the recording. Although you can hear your own voice, this is not only a great deal of current sound, but the worst is poor noise consumption and poor sampling. open the volume option (volume Cintrol) on the control panel of the computer, click "TOP"-"properties"-"Recording", and select the check boxes "stereo mix" and "mircrophone". These two are required. Click "OK, select mircrophone (Hook) and click "advanced". If the 1 mic boost in it is not checked, it is not enhanced; otherwise, it is enhanced. Ii. Noise Sampling:
The premise is that, after a recording key is clicked, starting the recording to the short audio track before the official singing, this audio track must look thicker than the mute area with the naked eye (you can choose a short audio track, click the effect-mute to try, this section of noise is called "Normal Noise ". select this normal noise, click "effect"> "noise elimination"> "Noise reduction". A screen is displayed, sampling the noise, closing the screen, returning to the single-tone editing screen, and selecting all single-voices, enter the noise reduction device again and adjust the noise reduction level below. Starting from 100%, the noise will decrease in the proportion of every 5%. Click Preview and listen to the noise in your ears, generally, I use 80%-90%. Do not change other parameters. After tuning, you can save the samples by clicking save, because this sample can also be used for other songs. After saving the samples, click OK, it will be OK; some singers should not use the above method for noise reduction. When using the above method, the sound will be severely distorted. Then, you can (1) Adjust the proportion to 20% and click OK; (2) sampling is performed again in the original sampling area, and the ratio is adjusted to 30%. (3) sampling is performed again in the second step. The ratio is 65%-75%.
After noise reduction, we can see with the naked eye that most of the places with no songs are the same as those with no voice, but there is still noise. At this time, you can mute those places without songs, in this way, the noise is completely eliminated. Generally, the noise is muted at the beginning and end of each segment of the song, and the distance between individual sentences and sentences is relatively large. Iii. breathing sound:
A good song needs to breathe too much, without breathing sounds too monotonous, too rigid, breathing too much and feels too messy, too unnatural. The recording is different from the singing scene, because of the microphone problem, the distance between the microphone and the mouth cannot be very good, so after you finish noise reduction, you can listen to your own single voice, mute those places that do not need to breathe, or click effect-waveform amplitude-strong limit. You only need to modify "input gain". The positive value indicates that the volume increases, and the negative value indicates that the volume decreases. Generally, the value range is-1 to-3, do not change other parameters. at the same time, you can go back to the recording screen and try again to see if it is natural to cancel the breathing sound. If it is not natural, you can skip it or reduce the breathing sound .... after the whole song is completed, the effect can be achieved. Iv. accompaniment:
If the accompaniment sounds great, the sound is too high, and the bass is too heavy, you can follow the "accompaniment processing" in "effect editing process table" to operate V. Volume:
After the effect is completed, return to the recording screen and listen carefully. First, check whether the volume of the accompaniment and dry sound is consistent. You can right-click the accompaniment or dry sound, adjust the audio block volume to adjust the volume of each audio track until it is coordinated. the second is to listen to the effect, including ECHO, tail sound, and breathing sound, aiming at perfection. 6. synthesis:
After all the information is completed, it means to compress and save it. On the recording page, place the indicator line at the front and right-click an empty audio track, click -after mixing all waveforms, click the to edit the screen. There are four white lines in the editing and two left and right channels in the editing, at this time, you can clearly see the mixed waveform, which should not exceed the first white line of the left channel, and the second white line of the right channel, (the highest part is generally the climax part of a song) that is, the top and bottom two lines. If the line is exceeded, the volume is too high. If the overall waveform is within the white line, far from the white line, it means that the volume is too small. Then you can click the effect-waveform amplitude-volume standardization, and adjust the value to around-95, so that the overall volume is relatively even, do not change it elsewhere. below is the save. Do not say it again? After saving the audio file, try the audio file again. Remember not to turn off the recording software. If there are any deficiencies, you can change the audio file again. After the software is turned off, the mixing operation will be reduced, which will greatly damage the sound quality, if it's okay, you can send a song! I believe it is a good work :) Effect editing process table preface to avoid the problem that the dry sound and accompaniment rhythm cannot match after multiple recordings appear in the same audio track, we recommend that you first create an empty track and insert it, recording on an empty track directly. The concept of an empty track is like a dry sound of a sound you have recorded, and it is in the mute state, you can select a record on the empty track, that is, a segment of the song. After recording the record, you can record another segment. Of course, it would be better if you can record it all at once, but don't forget that your goal is "perfect". Otherwise, recording on the empty track many times may also lead to no matching sound and accompaniment rhythm! Remember !!!
I. Recording:
Set to the left or right audio channel 16-bit recording (usually the right audio channel 16-bit) Ii. Noise Reduction-static noises-processing breathing sounds, and entering the first audition:
Only listen to dry voice, whether the sound is accurate, whether it is consistent and smooth, if not, sorry, please record this sentence or paragraph 3. Audio Track editing process:
1, pressure limit: effect-DirectX-Ultrafunkfx-compressorR3
Recommended parameters are:-26.0 2.0 20 0.0 0.1 300 2, the effect-DirectX-ReverbR3-(perfect ):
Recommended parameters are as follows: 0.0 718 3.4 172 64 100 1.0 500 1.5-4.0-1.3-6.3
(The final value of quicksong is-18.2) 3. Choose "effect"> "waveform amplitude"> "dynamic processing"> "Graphical"> "powerdrums" to select 3rd. (use the sound thinning method. skip this step) 4. effect-waveform amplitude-acoustic phase/sound field-mastering width, and select "smooth curve"
(Actually, it can be expanded to around 175) (for concert accompaniment, skip this step) 5. (1) effect-DirectX-tcnativereverb
Recommended parameter: Decay: 2.5 Rom & size: Small
Shape: Medium diffuse: Medium
Color: Bottom: To the rightmost; right: to the top and then down a grid
Predelay: 18 in: 0db
Out: 0db mix: 25%
(2) effect-common effect generator-reverb
Recommended parameters: 1000 10 10 20 100 15
Or select 1st or 2 items in the preset bar. (3) effect-common effect generator-simple reverb
Recommended parameters: 25 2518 86 3940 250 90 10 (4) effect-common effect generator-perfect reverb
Recommended parameters are as follows: 4283 154.1 200 45 110.8 39.6 0 (dedicated for concert) Note: This reverb only needs to be done once. Generally, you can select one accompaniment between (1) (2) (3) and concert accompaniment (3) 6. effect-common effect generator-echo
The recommended parameters are 44, 48, 31, 47, 40, and 43 respectively. The average echo of ECHO diffuse is 0. If the ECHO is too large, the smaller the parameter is, the smaller the ECHO is. 7. Graphic balancer-preset-30 band classicv (use this function if the sound is dry and you do not need to skip this step) 8. Results-DirectX-bbesonicmaximizer
Recommended parameters are as follows: 5.5 5.2-4 (use this step if the dry voice is stuffy. You do not need to skip this step) 9. accompaniment handling:
Performance-DirectX-Ultrafunkfx-ReverbR3-(accompaniment)
Recommended parameters are as follows: 0.2 off 0 50 100 1.0 500 0.1-4.0 4.7-0.3
The role is to make the sound and accompaniment more integrated. After such processing, the accompaniment has a three-dimensional effect. 10. Adjust the overall audio track so that the volume reaches the appropriate level. For the second review, add an appropriate echo to the echo of the individual (ending sound, slightly modify to the best status (not detailed) 11. Third Audition
Select effect-DirectX-Ultrafunkfx-SurroundR3 first in the edit Surface
Recommended parameters are as follows: the space is 1, the left/right is 0, and the front/back is 100.
Note: When performing the chorus effect, you can adjust the left/right to-15/15 for the two-person chorus. If there are many people, you need to adjust the front/back to 80-90, this sounds like a mess, and the audition effect is better! After completing the test, let's try and make a few changes to the best state (not detailed)
Audition-modifier:
(1) The climax part is too stuffy, or the overall sound is still too stuffy, you can use the graphics balancer-preset-gentle low cut
(2) If you feel that the reverb effect is not enough in some places, monotonous, and there is no stereoscopic effect, you can use the effect-commonly used effector-reverb.
Parameters are adjusted to 1200, 238, 626, 100, 1200, 25, or 83 to adjust the degree of reverb. 12. merge into one audio track-volume standardization-effect-DirectX-waververb
Recommended parameters: 180 1.20 3703 0.7 echoverb var: 0 185-3.8 2032
-4.5 1.0 0.78 88.7 66.4 2.60 0.0 3-0.0
This step is done twice to further integrate accompaniment and voice 13. effect-waveform amplitude-volume Standardization
You only need to standardize to and left/right association, the ratio of standardization is between 95 and 90 Parameter settings (1) noise reduction. Noise reduction.
There was a noise before the voice, that is, environmental noise. Select the environmental noise, select "effect" on the menu bar, and then select "Refresh effect List". A dialog box is displayed, after "yes" is selected, select "noise elimination" in "effect" on the menu bar, select "Noise Reduction", and select "noise sampling ", then press "close ". then, select the noise generator in "effect" in the menu bar and press OK to eliminate the environmental noise during the recording process. this is only the elimination of environmental noise, and the ending sound at the end of the human voice should also be eliminated. Otherwise, the effect of the whole song will be affected. This noise has a dedicated plug-in "waves" rvox effect, this effect can cut off the ending sound at the end of the voice. We recommend that you set it to be skipped. Otherwise, the beginning and end of each sentence will suddenly disappear. (2) motivate people. Double-click the voice track to switch to the waveform editing page, select all waveforms, and then select the "bbesonicmaximizer" plug-in "derectx" in "Effect". Then, you will see three knobs, the first is the bass, the second is the treble, and the third is the total output volume. you can adjust the overall volume of the high and low voices according to the voice of people. The voice you are recording is not very strong. This requires a high tone to motivate you. This sounds nice, if you don't believe it, try it. (3) pressure limit. After waves 4.0 is installed, select "wavesc4" in "derectx". The adjustment window is displayed. at this time, we need to adjust the high frequency and low frequency according to our own voice. When we start to use the software, we may not know how to adjust the data. In this way, we can select "LOAD" in the adjustment window ", after entering, you will see a lot of results. You can choose the fourth "Pop Vocal", and then press OK. the role of the pressure limit is that the voice frequency should not be "noisy", and the low frequency should not be "noisy ". At first, I don't know how to use the above method. I will adjust the correct data according to my voice when I become proficient. (4) enhance the voice intensity and expressiveness. After the "ultrafunk FX" effect is installed, there will be an effect device named "compressor R3". The effect of this effect is to enhance the voice strength and expressiveness. After opening it, there will be four small boxes on it, different data may have different effects. When you don't know how to use it, you can input the four data. The first input is-20, the second input is 4.0, and the third input is: 16 fourth input: 7.0 except for the top four, there are two below, the first input: 40 the second input: 200 and then press OK to enhance the voice intensity and expressiveness. the above provides only rough data. The specific data depends on everyone's feelings and is finally determined. (5) reverb. After the "ultrafunk FX" effect is installed, it will be called "reverb R3. this work requires a lot of care. Different recording environments and different kinds of music-style reverb effects are different. this requires continuous accumulation of experience. For rooms with large volume and insufficient sound absorption, the manual reverb time of the caster is shorter. the time needed for male singing should be shorter; the time needed for female singing may be longer. professional singers should spend a little less time in reverb; otherwise, they will damage the features of the original tone. Amateur Singers can spend a longer period of reverb time to mask the deficiencies of the sound and so on ...... Friends who started to use this software can enter the data I provided. There are 13 small boxes in total. First: 0.0 Second: 75 Third: 7.1 Fourth: 0 Fifth: 50 sixth: 100 Seventh: 1.0 Eighth: 500 Ninth: 2.2 Tenth: 7.8 11th: 0.0 12th:-14.3 13th:-12.3. I again stated that what we provided above is not standard data. This is just for friends who are just using this software. The specific data depends on their own ears. I would like to tell you that the size of the reverb is the last one, that is, 13th. If you want to listen to it in detail, increasing the reverb will make you feel open. Even amateur singers can just add a bit more, not too large. (6) balanced voice. After the "ultrafunk FX" effect is installed, it will be called "equalizer. the main function is to balance the voice of people, so that the high frequency can be adjusted to clear and transparent without noise; the low frequency can be adjusted to clear and natural without turbidity. if you start using this software, you can use the data that I provided first, instead of standard data. You need to explore the specific data on your own. The effect device requires three columns of data. Here I will write them in one column. column 1: 40; 60; 200; 800; 4600; 15000. column 2: 1.0; 0.8; 0.8; 0.6; 0.6; Column 3: 0.5;-0.4; 2.2; 0.3; 0.0; 6.5; 0. 0. input the data and press OK. |
