Details on TP-link router settings (illustration)

Source: Internet
Author: User

The router setting diagram is designed for beginners who build networks. There are no technical points, but the steps are complicated and difficult for them. Here we will show you the entire process of specific operations, this allows you to easily master vro settings.

Preparation of TP-link router settings

The first condition is: one vro (four ports, eight ports, 16 ports, or more). If you have many computers, you can buy multiple vswitches. there are several cable connections. One Telecom mode (or you don't need the mode if you are a leased line) and at least two PC computers (if you only have one, you can use a vro, however, the meaning of using a vro is lost.
In fact, TP-Link company out of the router, such as TP-LINK TL-402M or 401m or other models of TP-link router, most of the ways to open the route almost. The following TP-LINK TL-402M as an example, please see Picture 1

 

 

Figure 1tp-link TL-402M

The TP-link router is introduced here. You only need to follow the picture to correctly connect the PCs, Telecom broadband modes, and routers to each other, so a network has been set up. the following describes how to enable the routing function.

TP-link router settings earlier:

If all cables have been connected. we can open a connected pc at any time. enable the network neighbor attribute (Image 2), local connection attribute (image 3), TCP/IP protocol attribute (Image 4), and set the IP address to 192.168.1.2 subnet: 255.255.255.0 Gateway: 192.168.1.1 (image 5) are you sure you want to configure the DNS After configuring the vro.

Note: You can go to the control panel to set the network connection.

Take XP as an example. See the details from Figure 2 to figure 5.

Figure 2 enable the network neighbor attribute

Figure 3 Local Connection Properties

 

Figure 4 TCP/IP Protocol attributes

 

Figure 5 set IP addresses

By the way, I would like to remind you that IP address ranges can be set between 192.168.1.2 and 192.168.1.254. Do not set the same IP address to multiple computers. This will cause IP address conflicts. Remember.

Then you can open Internet Explorer on the desktop and enter 192.168.1.1 and press Enter. See figure 6.

 

Figure 6 enable Internet Explorer on the desktop

Enter the user name and password. The default user name and password are admin, which is also written in the vro manual. Enter the name and press enter to enter the vro configuration interface.

Note: The default IP addresses of tplink routers are basically 192.168.1.1, And the passwords are basically admin.

Vro settings for TP-link vro:

Enter the router interface for the first time. See figure 7.

 

Figure 7 enter the vro Interface

Select the setting wizard. See figure 8.

 

Figure 8 select Setup Wizard

Next, see Figure 9.

 

Figure 9 next step

We select ADSL virtual dialing here. Most of us choose it. The other static data is selected by the leased line. We will not detail it here. We know broadband users, tietong, China Netcom and other virtual dialing users, select it. Next, see Figure 10.

 

Figure 10 next step

Click Next to see image 11. Click Finish to set the route.

 

Figure 11 next step

Then set the network parameter and Wan port at the point. See Figure 12.

 

Figure 12 Network Parameters

Now, all the configurations in the vro are set. Now we only need to restart the vro. Click the system tool and restart the vro. It will take a few seconds. See figure 13.

 

Figure 13 restart a vro

At this time, we close the configured webpage window and connect to other computers to access the Internet.

Note: Because the DHCP service of the vro is automatically enabled, you only need to connect to the PC, and the vro will assign an IP address to the computer. Therefore, no other computer needs to be set, connect the vro or vswitch directly with a network cable to access the Internet.

TP-link vro settings:

Of course, you can also manually set the IP Address:

◆ IP setting range: 192.168.1.2-192.168.1.254

◆ Subnet: 255.255.255.0

◆ Gateway: 192.168.1.1

◆ DNS: You can set the DNS provided by the local telecom to the preferred DNS and backup DNS.

If you do not know the local DNS address, you can set the preferred DNS address to 192.168.1.1, that is, the gateway.

Okay. Now, we need to set the DNS address of this PC. The method will not be much said. Open the local connection attribute of the network neighbor attribute, TCP/IP protocol attribute, see Figure 14 for the local telecom DNS address. figure 15. DNS is the gateway address

 

Figure 14 local telecom DNS address

 

Figure 15 DNS is the gateway address

Note: The above figure 14 sets the local telecom DNS address, and friends need to set it according to their local telecom DNS address. I will introduce you to all the vro settings. I hope you can understand and understand vro settings.

 

Transferred from: http://network.51cto.com s

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.