FAQs about wireless router disconnection

When we use a vro many times, the disconnection problem is not unexpected. Here we summarize some common problems and provide solutions.

In many cases, the wireless router is not caused by the wireless router itself. In this case, first check the idea of the front-end device. First, check whether the front-end broadband device has a disconnection problem.

Connection failure 1 of wireless router disconnection

The high-frequency attenuation is too large due to reasons such as loose cables or poor connection, oxidation or halide of the contact piece of the crystal head, and poor line contact.

Solution:

Check whether the cables connected to the network are inserted on the correct port, and whether the broadband MODEM line is correctly connected to the WAN/Internet port of the wireless router. Try replacing the network cable connected to the wireless router, and check whether the workmanship and quality of the crystal head, such as the flexibility of the Tongue Piece, are sufficient. The loose and halide of the crystal head will also lead to network disconnection. The wide area Port indicator of the ADSL terminal is shining, and the terminal cannot be activated or occasionally activated. Check whether the connection between the user line and the telephone line is correct and whether the connection is detached. If necessary, try again.

For wired broadband, check the status of the indicator on the Cable Modem. If the status of the indicator is abnormal, check whether the connection between Cable Modem and the coaxial Cable of the Cable is reliable, damaged, or loose. Check whether the Cable TV reception is normal, if the effect of a TV program is obviously poor or you cannot see it at all, you can call the cable TV customer service center.

In this way, the possible range of problems can be reduced step by step to determine whether the problem is caused by broadband equipment, service providers or wireless routers.

2 ADSL line faults caused by wireless router disconnection

The incoming telephone line is too long, there are too many connections, or there are some interference sources.

Solution:

The customer's line quality is too bad. Try using ADSL to access the Internet separately. If the line is also dropped, you can ask the ISP to check the quality of the incoming line. Check whether there are cordless phones around ADSL), air conditioners, washing machines, refrigerators, and other devices with serious electromagnetic interference. If so, remove them, do not share a power cord. voltage instability may also cause some MODEM to fail ).

You can use the following common methods to determine the fault location: Whether you can call or access the Internet, indicating that the line is normal. The cause may be a problem with the Internet or ADSL terminal. If you can access the Internet, you cannot make a call, bianming's external line is normal and the interconnected network is normal because of indoor telephone connection problems or problems ranging from ADSL racks to programmable switches. It is possible that the external line is disconnected because the phone cannot be called or accessed, or other problems; poor external insulation of the user end. When the user accesses the Internet, the WAN lamp with the telephone handle is off or the broadband signal cannot be synchronized. Generally, the external insulation is poor or the connection is not in good contact, after the external line is repaired, the fault can be rectified.

Wireless Router disconnection problem 3 separator Problem

The splitter is faulty and the connection is incorrect.

Solution:

Do not understand the separator, directly connect the telephone line to ADSL, and try using ADSL alone to access the Internet. Correct Connection to the ADSL signal Splitter. The correct connection method is to mark the input end of the telephone Line from the telecom Bureau to the signal Splitter as "Line "); connect one end of a telephone line to the voice signal output port of the signal splitter, which is generally labeled as "Phone number)" and the other end to your Phone. The ADSL output port on the splitter is generally labeled as "ADSL" or "Modem" and is connected to the ADSL Jack of the adsl modem through a telephone line.

 

It must be noted that no other telephone equipment is available between the signal separator and the external line. Any access to any extension, fax machine, anti-theft device, and other equipment will cause ADSL faults, the extension and other devices can only be connected to the audio port separated by the separator. If you do not need a phone number next to the PC, you can connect the telephone line directly to the ADSL Modem. The splitter is installed in front of the phone.