DVD Suppression RMVB Tutorial + synchronous Push Watermark _ Application Tips

Step One:
First copy the DVD into your hard disk, because the DVD itself with the encryption, directly copied inside the content is not, must use a number of specialized software to replicate, here I recommend a good green software: Smartrippe has been uploaded to the annex
Put the DVD in the optical drive first, then turn on the Smartrippe (SR), then the SR will automatically scan the DVD will go to the main interface, and sometimes will be prompted not to read, then you can take out the disc and then put in a few tries, If you still do not think that is not read or disk bad met these circumstances simply give up, if you want to suppress words, you can change the other software to try!
Note: The folder that holds the file is best renamed: a

Lest there be any inexplicable mistake.

screen.width-500) this.style.width=screen.width-500; "Border=0>

screen.width-500) this.style.width=screen.width-500; "Border=0>

screen.width-500) this.style.width=screen.width-500; "Border=0>

Click Settings to set the related properties:

screen.width-500) this.style.width=screen.width-500; "Border=0>

After all the properties have been set, click Start to copy:

screen.width-500) this.style.width=screen.width-500; "Border=0>
After the copy is completed, several files in the following diagram are mainly generated:

screen.width-500) this.style.width=screen.width-500; "Border=0>
As long as the Vts_01_0.vob file is retained, all other files are deleted and the Vts_01_0.vod file is renamed A.vob

extract subtitles in movie

screen.width-500) this.style.width=screen.width-500;" Border =0>
Here you should note that you must open the Video_ts folder in the DVD disc and select Open * in the file type. Ifo file, otherwise it is not the caption of the

screen.width-500) this.style.width=screen.width-500; "BORDER=0>

screen.width-500) this.style.width=screen.width-500 "BORDER=0>
Click OK after the caption extraction work is done, If you also want to make some adjustments to the resulting captions, you can open the resulting subtitle file changes directly.

screen.width-500) this.style.width=screen.width-500, "Border=0>

" also explains that the subtitle structure presented in the DVD is different from the regular subtitles. You can't change the size and font, and if your computer isn't strong enough, it's best not to open the generated subtitles. SUB file

Step Three:
First install EasyRealMediaProducerV1.8, set up and start setting up.

screen.width-500) this.style.width=screen.width-500; "Border=0>

After the running interface is as follows, click Add button Select the VOB movie file you want to suppress

screen.width-500) this.style.width=screen.width-500; "Border=0>

screen.width-500) this.style.width=screen.width-500; "Border=0>
Select all the files to be compressed after the parameter settings, select the file, point parameter settings to set

screen.width-500) this.style.width=screen.width-500; "Border=0>
1. About setting up an item for compression
, the pressure over the film should be clear, used to set the rate of suppression, the dynamic rate of the maximum code rate and the greater the average rate of the code is a good film (this refers to BMVB file) the larger the volume, too lower will affect the quality of the film,

① film source better (such as DVD9, etc.) action film, the scene of larger films (such as The Lord of the Rings, The matrix) the maximum rate of the general 700~800 around, the average rate of the largest not more than 500!
② Chip source general (such as Dvd,vcd,dvdrip format), which is the majority of repression, the general maximum rate set in 650~700, the average rate set at 400 basic can be maintained on the basis of quality to press out the volume of moderate film.
③ chip source is poor, here mainly refers to some of the gun version of the film, this type of film maximum rate set in 500~650, the average rate of 300 can be
changes to FPS can result in some formats that cannot be suppressed such as: *. VOB file, please note2. About video mode settings

Normal Motion video General effect ...
Smoothest Motion After several tests recommended not!
Sharpest Image suitable for animation, film Suppression!
Slide Show remembers is slide mode, with this press screen will be a meal like play slide
No video Select this will not be compression


Video coding on the choice of RealVideo 9, choose 10 I think it is a waste of time and the effect of a small difference ....
3. About the setting of audio coding of course is the bigger the better, see your ears like how it, but not too big, big will also affect the volume of the generated RMVB
The volume is directly up to 12, not much to explain.

Then check again, all files in the folder must have the same name. A.vob a.idx a.sub A.ssa
Check the correct after the point is determined to press the film, followed by a long wait ... .If you want to put the film on both the caption and the watermark, then look down:


Method
Create a new "text document"
Enter the following contents in the inside
__________________________________________

Loadplugin ("VSFilter.dll") (Do not change this line)
Directshowsource ("D:\a\a.vob") (change d:\a\ to the path in your machine)
Textsub ("D:\a\a.ssa") (change d:\a\ to the path in your machine)
VobSub ("D:\a\a.idx") (change d:\a\ to the path in your machine)

__________________________________________
then change the text document extension to *.avsopen EasyRealMediaProducerV1.8, add files do not select the VOB file, directly select just do the Avs file, set good parameters can be pressed film