How to clear various projection bulbs!

At the beginning of the school, the multimedia in the school broke down a lot, except for the 12 new sets, the rest basically had problems.

 

For two consecutive weeks, the service was mostly used for multimedia maintenance. It was very busy and tiring.

 

Fortunately, the newly recruited Mr. Xu is still awesome, diligent, and intelligent.

 

In the past two days, the projector has to be cleared several times.

 

So I collected and sorted out various projector resetting methods.

 

********************************

 

Sharp DLPProjector resetting

In the standby status, press "right" + "down" + "enter" + "power" at the same time.

Sharp (Sharp)Projector resetting Method

Cn450s cn450x cn500x resetting method: press the projector at the same time in the STANDBY state (do not boot); input enter undo on 3 seconds or more he can boot. If the light bulb is displayed, 100% indicates that the light bulb is cleared.

An100s an100x an120s press and hold (in standby mode) on the projector; +; and auto sync at the same time, press the on and;-; button on the projector if the display lamph h indicates that the light cannon has been reset

SonyRepair menuGo to boot, press OK + menu + OK, and then press

Sony resetting Method: Reses + Left + right + OK (applicable to most Sony models), some panels on the Panel, the Panel is not healthy with the remote control

Plus (PLoS)Projector resetting Method

Plus U2-811 U2-815 U2-815C U2-1110 U2-1130 U2-X1130C
The light bulb is cleared within 1100 hours. Choose time from the menu. Press the remote control for about 8 seconds.
After 1100 hours of use, you can directly press the remote control on the power-on status for about 25 hours.

Plus U3-810SFC U3-1080SFC U3-810WZC U3-1080WZC 4-161 U2-X200UC
V-1080C V-807C V-1100C U2-850 U2-1500 U2-850W U2-1500W U5-121
Clear the light bulb timer in the menu

EPSON (EPSON)Projector resetting Method

EMP-5350/5300 series clear in addition to short circuit also has other methods, is the menu combination key:
Help + menu: Call up the menu, and press and hold the tracking + and tracking together;

EMP-7600/5600 series of clearing method:
Is it stuck? In about 10 seconds, the menu is cleared.

EPSON bulb clear method: 100ma fuse that has been disconnected. transient connection. OK!

EMP-820/811/800 series all in the menu clear;

EPSON projector resetting method (only applicable to machines with resistors at the lamp rack): There is a small resistor at the lamp Rack (used for resetting ), you just need to short the corresponding 4 small needles in the machine. This will be annoying, and if the short circuit is not good, the motherboard may be burned.

NECHow to clear the machine timing?

NEC projectors can be cleared with options in the menu.

 

In addition, the old models and the plus models are the same in two cases: 1. After Entering the light bulb timing menu under normal power-on status, press and hold the "on" Key of the remote control for about 10 seconds; second, if the device cannot be properly started, press the "off" Key of the remote control in the standby mode for about 20 seconds. Try it.

EPSONWhen some models are deprecated

Epson500, 700, 710, 50, 70: Help -----> keystone + ---------> "sourse, Keystone +" --------> "sourse + keystone -"

Epson5350, 7250, 7350, 8000, 9000, 8100, 7700, 7600,: Help + menu --------> "tracking +, tracking-" ----------> "avmute, Sync +"

 

Clearing method of BenQ. Press power and then press the cross key.

Press the power key to connect to the power supply.

Hitachi projection erasingYes: you can press the peset key for a long time to display the clear menu !! 11

Toshiba projector resetting: Press power supply + menu + OK + input without power supply, press and hold power without power supply for 3 seconds

Toshiba T600/t400 series projector to restore factory value: Press and hold the OK key for 3 seconds at startup;

 

Mitsubishi(Left + right) + enter

Mitsubishi, Left + right + Power Supply

The method for resetting Mitsubishi S250 is: Upper arrow + enter + startup key

 

Sony resetting Method: Preparation + Left + right + OK (applicable to most Sony models)

Sharp100 s,100x,200------- Etc. projector light bulb resetting Method
Operate on the projector: press the-, +, and autosync keys, and then press the power button.

 

Hitachi Machine,

 

In the projector menu, after you find the time used by the projector, press and hold the reset key for 5 seconds, and you will be prompted to reset it.

Hitachi projector resetting Method

Hitachi projector method:
A. press the reset key for 5 seconds and press the reset key in the pop-up window. This method is suitable for most Hitachi projectors )!
B. Find the time option in the menu, right-click the 5 banknotes, and press the reset key in the pop-up window!

LGWhen the jt50 projector is cleared, press and hold the up key until the light bulb uses time in the lower right corner of the projector and then click the menu key to clear the light.

3 m: How to clear Hitachi OEM: press reset for 3 seconds when the device is started, and a dialog will appear at a time. If you select 0, the mp8030 clearing method is to press the timer key on the remote control for two seconds, select zero in the displayed dialog box.

3 m8746 clear: Long press reset to display the light bulb time, press the left and right keys to move the cursor to 0000, and press the left and right keys to make the menu disappear, OK!

Morning StarCX-1 and Sanyo PLC-XP18N are clear 0 in the menu

Panasonic557Projector light bulb reset method

The resetting of the Panasonic 557 projector light bulb is different from that of the other model. The specific method is as follows: Open the "menu", select "set" with the up and down keys, and select "yes" for the projector light bulb "; turn off the power switch (not the "power" key on the panel.

Panasonic (Panasonic)Projector resetting method [resend 〕

Panasonic projector resetting method: First press "menu" to find the light bulb use time, then press "enter" for three seconds, after "power off" appears, turn off the power and restart OK!

InFocusHow to clear the LP 130 light bulb? Press menu and reset for more than 5 seconds (BOOT status)

Morning Star500/600Series resetting
Simply turn out the light bulb timer and select reset.

Morning StarTl460Projector reset light bulb timer method

Press the + and autosync buttons on the projector and press the on and UNDC-buttons on the projector. The screen will display 0000 after the projector is started.

Sanyo (Sanyo),Eiki (Love it),Canon (Canon)Projector resetting Method:All in the menu, with lamp in the column, all are yes

Sanyo z1

Menu and input enter the factory mode in five seconds.
Select and input enter the service mode in five seconds.

Note:
The two add up to thousands of settings. Before the change, remember to copy the factory value.

Phillips projector resetting Method: Start, select the lightbulb time bar from the menu, and press OK on the projector for 3 seconds.

Mitsubishi projector resetting Method: Press left + right + power supply in standby mode

Sharp 300 s, X is to press enter, down arrow, left arrow at the same time on the remote control and then press on boot, you can

Fujitsu:Press and hold the OK key, and press the power key three times. [applicable to some hosts]

Clear Morning Star Projector
Morning Star CX-59/69/550/650590/690 models are sharp OEM, clear and into the repair menu see sharp corresponding models;
Morning Star CX-500/505/600/610/615 models are Li Xun OEM, clear and into the repair menu see Li Xun corresponding models;

How to clear and enter the repair menu of Li Xun

Press, top, left, and right when the device is on or without a signal to enter the menu. Clear the light bulb and set the color temperature.

LGHow to clear the machine:Press the up key until "lamp hours Info" is displayed, and then press menu !!

This article is from "new time! New Way !" Blog, please be sure to keep this source http://bannerpei.blog.51cto.com/66697/1551961

How to clear various projection bulbs!