How to install and configure the network startup server in Linux (PXE + tftp + DHCPD)

Source: Internet
Author: User
Tags file transfer protocol
Document directory
  • 1. Glossary used in this article
  • 2. PXE Principle
  • 3. PXE boot server configuration process
  • 4. Summary)
1. Glossary used in this article

 

PXE
PXE (pre-boot executionenvironment) is an Intel-designed protocol that enables computers to be started over the network rather than from local hard drives, optical drives, and other devices. Modern NICs are usually embedded with Rom chips that support PXE. During computer boot, the BIOS transfers the PXE client to the memory for execution and displays the command menu. After the user selects the command, the pxeclient downloads the pxeclient from the remote operating system to the local computer for running.
DHCP
DHCP (Dynamic Host Control Protocol) Dynamic Host Control Protocol. Used to centrally and dynamically assign IP addresses to clients.
TFTP
TFTP (Trivial File Transfer Protocol) is a File Transfer Protocol with a low overhead. The syntax is similar to FTP. Because of its simplicity and efficiency, it is often used to update operating systems and configurations of network devices.

 

2. PXE principle 2.1. PXE client API (Architecture)

 

Figure pxe api Architecture. (Image Source: PXE Specification Version 2.1)

Note: When the BIOS loads the PXE client into the memory, it has the capabilities of DHCP Client and TFTP client.
PXE client is capable of DHCP Client and can obtain IP addresses through DHCP server.
PXE client is capable of TFTP client. You can use TFTP to download files such as kernel image.

2.2. PXE boot flowchart (PXE boot)

 

The startup process is described as follows:

  1. The PXE client broadcasts the dhcpddiscover message to the UDP port 67.
  2. After receiving the broadcast message, DHCP server or DHCP proxy sends the dhcpoffer (including the IP address) message to port 68 of PXE client.
  3. The PXE client sends the dhcprequest message to the DHCP server to obtain the boot file name ).
  4. DHCP server sends the dhcpack (including network Bootstrap program file name) message to PXE client.
  5. PXE client obtains the NBP (Network Bootstrap program) file from the boot server.
  6. PXE client downloads NBP from the TFTP server, and then executes the NBP file on the client.

Note: After NBP executes initialization, NBP downloads other required configuration files from the TFTP server by default.
At this time, the PXE startup process has been completed, and the rest of the work is completed with NBP.

For example, pxelinux.0 (NBP) downloads the default configuration file to display the menu and starts different kernel images as needed.
If it is the NBP of RIS (Windows installation), Windows boot loader is started to execute the widows installation and deployment task.

3. PXE boot server configuration process

The following configurations and tests are completed on centos5. For more information about other systems, see!

3.1. DHCP installation and configuration

During the PXE boot process, the PXE client obtains the IP address and NBP file name through the DHCP server, downloads the NBP file from the TFTP server, and runs the file on the client to start the computer.

  1. Verify that the DHCP software package is installed in the system.
  2. Edit the/etc/DHCPD. conf configuration file. The configuration file content is as follows:
    [Root @ Linux] # Cat/etc/DHCPD. conf
    Ddns-Update-style interim;
    Allow booting; # define the ability to start PXE
    Allow BOOTP; # define support for BOOTP
    Next-server 192.168.0.1; # IP address of the TFTP Server
    Filename "pxelinux.0"; # Bootstrap file (NBP)

    Default-lease-time 1800;
    Max-lease-time 7200;
    Ping-check true;
    Option domain-name-servers 192.168.0.1;

    Subnet 192.168.0.0 netmask 255.255.255.0
    {
    Range 192.168.0.128 192.168.0.220;
    Option routers 192.168.0.1;
    Option broadcast-address 192.168.0.255;
    }

    Note: In the/etc/DHCPD. conf configuration fileFilename "pxelinux.0 ";
    The file directory is the root directory (/tftpboot by default) relative to TFTP ),

    Therefore, the absolute path of the file is/tftpboot/pxelinux.0 ". You can also specify it as another path.

  3. After the configuration is complete, restart the DHCP service and set it to boot automatically
    [Root @ Linux] #/etc/init. d/DHCPD start
    Start DHCPD: [OK]
    [Root @ Linux] # chkconfig -- level 35 DHCPD on
3.2. install and configure the TFTP Server

During the PXE boot process, the PXE client uses the TFTP protocol to download and execute the bootstrap file from the TFTP server.

  1. Verify that the TFTP-server software package is installed in the system.
  2. Configure the TFTP service. The tftp service is managed by the xinetd service.

    Edit the/etc/xinetd. d/TFTP file and change disable = yes to disable = No. The configuration file content is as follows:

      [root@linux]# cat  /etc/xinetd.d/tftp
    # default: off
    # description: The tftp server serves files using the trivial file transfer /
    # protocol. The tftp protocol is often used to boot diskless /
    # workstations, download configuration files to network-aware printers, /
    # and to start the installation process for some operating systems.
    # default: off
    # description: The tftp server serves files using the trivial file transfer /
    #protocol. The tftp protocol is often used to boot diskless /
    #workstations, download configuration files to network-aware printers, /
    #and to start the installation process for some operating systems.
    service tftp
    {
    socket_type= dgram
    protocol= udp
    wait= yes
    user= root
    server= /usr/sbin/in.tftpd
    server_args= -s /tftpboot
    disable= no
    per_source= 11
    cps= 100 2
    flags= IPv4
    }

    Note: the root directory of the TFTP server is/tftpboot. After the configuration is complete, restart the xinetd service to make the TFTP server take effect.

      [root@linux]# /etc/init.d/xinetd restart
  3. The bootstrap file configuration (NBP) is provided by the syslinux software package. If syslinux is installed, copy the pxelinux.0 file to the/tftpboot directory:
      [root@linux]# rpm -ql syslinux | grep "pxelinux.0"
    /usr/lib/syslinux/pxelinux.0
    [root@linux]# cp /usr/lib/syslinux/pxelinux.0 /tftpboot/
  4. Configure the configuration file used by pxelinux.0 (NBP)
  • Next, create the/tftpboot/pxelinux. cfg/directory to store the client configuration file.

      [root@linux]# mkdir /tftpboot/pxelinux.cfg
  • The default configuration file is default. The file content is as follows:
    [Root @ Linux] # Cat/tftpboot/pxelinux. cfg/Default

    Default Linux # by default, the startup kernel marked in 'label Linux 'is started.
    Prompt 1 # display 'boot: 'prompt
    Timeout 60 # Wait time-out period, in the unit of 1/10 seconds. After timeout, the default label is automatically started.
    Display boot. MSG # display boot. MSG content, the file path is relative to the root directory of the TFTP server (default/tftpboot), so boot. the absolute path of the MSG file is/tftpboot/boot. MSG.
    F1 boot. MSG # file displayed after pressing 'f1'
    F2 options. msg
    F3 General. msg
    F4 Param. msg
    F5 rescue. msg

    Label 1 # 'label' specifies the keyword you enter at the 'boot: 'prompt.
    Kernel Linux/rh44-x86-32/vmlinuz
    Append initrd = Linux/rh44-x86-32/initrd. IMG ramdisk_size = 8192 Ks = http://install.test.com/conf/ks_module.cfg ksdevice = Link

    Label 2
    Kernel Linux/rh44-x86-64/vmlinuz
    Append initrd = Linux/rh44-x86-64/initrd. IMG ramdisk_size = 8192 Ks = http://install.test.com/conf/ks_module.cfg ksdevice = Link

    Label 3
    Kernel Linux/rh46-x86-64/vmlinuz
    Append initrd = Linux/rh46-x86-64/initrd. IMG ramdisk_size = 8192 Ks = http://install.test.com/conf/ks_module.cfg ksdevice = Link

    Label 4
    Kernel Linux/rh46-x86-32/vmlinuz
    Append initrd = Linux/rh46-x86-32/initrd. IMG ramdisk_size = 8192 Ks = http://install.test.com/conf/ks_module.cfg ksdevice = Link

    Label 5
    Kernel image/Linux/rh38-x86-32/vmlinuz
    Append initrd = image/Linux/rh38-x86-32/initrd. IMG ramdisk_size = 8192 Ks = http://install.test.com/conf/ks_module.cfg ksdevice = Link

    Label 6
    Kernel Linux/rh38-x86-64/vmlinuz
    Append initrd = Linux/rh38-x86-64/initrd. IMG ramdisk_size = 8192 Ks = http://install.test.com/conf/ks_module.cfg ksdevice = Link

    Note: pxelinux.0 and pxelinux. cfg must be in the same directory by default.

3.3. pxelinx.0 (NBP) program configuration file search sequence

Since multiple clients can boot from a PXE Server, the PXE Boot Image uses a complex configuration file search method to find the configuration file for the client.

Assume that the MAC address of the NIC of the client server is 88: 99: AA: BB: CC: DD and the corresponding IP address is 192.168.1.195. The pxelinux.0 program search order of the client server is as follows:

  1. First, use the MAC address as the configuration file that matches the file name. If it does not exist, continue searching.
  2. Second, search by IP address. Search by configuration file named in hexadecimal format of IP address, from small to large, divided into search (subnet mask from small to large). If it does not exist, continue to search.
  3. Finally try the default file

In general, the order of the files searched by pxelinux.0 is (the result can be obtained through tcpdum ):

  /tftpboot/pxelinux.cfg/01-88-99-aa-bb-cc-dd
/tftpboot/pxelinux.cfg/C0A801C3
/tftpboot/pxelinux.cfg/C0A801C
/tftpboot/pxelinux.cfg/C0A801
/tftpboot/pxelinux.cfg/C0A80
/tftpboot/pxelinux.cfg/C0A8
/tftpboot/pxelinux.cfg/C0A
/tftpboot/pxelinux.cfg/C0
/tftpboot/pxelinux.cfg/C
/tftpboot/pxelinux.cfg/default
4. Summary)

 

5. ks. cfg file of PXE ---- memo

# Kickstart file automatically generated by Anaconda.

Install

URL -- URL http: // 192.168.1.100/centos4.5

Lang en_us

Langsupport -- default = en_US.UTF-8 zh_CN.UTF-8 en_US.UTF-8

Keyboard us

Mouse

Text

# Xconfig -- card "ATI es1000" -- videoram 16384 -- hsync 28-64 -- vsync 48-78 -- resolution 800x600 -- depth 16

Network -- device eth0 -- bootproto static -- IP 192.168.1.200 -- netmask 255.255.255.0 -- gateway = 192.168.1.1 -- hostname = test.insenz.com

Rootpw -- iscrypted $1 $ U // jmrgx $ dw9ytxblcyaafvkvwocnf0

Firewall -- disabled

SELinux -- disabled

Authconfig -- enableshadow -- enablemd5

Timezone Asia/Shanghai

Bootloader -- location = MBR

Zerombr Yes

Clearpart -- Linux -- initlabel

Part/boot -- fstype ext3 -- size = 150 -- ondisk = SDA -- asprimary

Part swap -- size = 4096 -- ondisk = SDA

Part/-- size = 20480 -- fstype ext3 -- ondisk = SDA

Part/home -- fstype ext3 -- size = 1 -- grow -- ondisk = SDA

Part/data -- fstype ext3 -- size = 1 -- grow -- ondisk = SDB

Skipx

% Packages -- resolvedeps

@ Editors

@ Emacs

@ System-Tools

@ X-software-development

@ Dialup

@ Chinese-support

@ Development-Tools

-Ckermit

Kernel-devel

Kernel-smp-devel

-Bluez-pin

-Gamin-devel

-Openipmi-Tools

Vlock

Iptraf

Lslk

E2fsprogs

-Xdelta

-Zsh

Sysstat

Kernel-SMP

Grub

-Iiimf-libs-devel

% Post

Related Article

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.