How to install WIN10 and Linux dual system a lot of getting started small partners want to experience a Linux pleasure, but the data on the windows on the deletion must not, helpless had to give up. Small series through some online tutorials, a little bit of tidying up the WIN10 and Linux dual-system installation tutorials. Note: Please first pull to the bottom, select vote, and then watch, thank you = ~_~ = Tools/Raw Material laptop lenovoG40 win10 linux ubuntu14.xxxx ultraiso u disk X1 "Better than 4G" perseverance method/Step 1 First of all, the No. 0 step, in the tail of the disk compression out of a roughly 50G of space, super budget, compressed space here do not have to set up a new partition, waiting for the back, the figure does not understand can Baidu. The first step, of course, is to download the image of Linux ubuntu14.x, this small partner can Baidu, go to the regular website now, here, I first provide a site: mirrors.xmu.edu.cn, Xiamen University Information and Network Center. There are many Linux versions inside. There are deepin cenos ubuntu what anything. 2 The second step, download the UltraISO soft Disk Pass tool, after the download is complete, insert the USB stick, use UltraISO to put Linux UBUNTU14. X this ISO file "write hard disk image" to the USB stick, remember to back up the data inside the USB flash drive, do not let the computer hibernate during the writing process, so as not to damage the U disk. After writing, there will be a corresponding success prompt, after successful click Back. 3 The third step, backup the important data of the computer, please refer to Baidu for detailed methods. Tip: Important data includes documents, archives, project files, software account name passwords, billing software information, and more. Backup PC options in Control Panel--file history can be found. 4 Fourth step, hehe, set the BIOS. The author here is Lenovo G40 Win10 X64 Uefi+gtp, after the shutdown, press the small button on the left of the computer to enter the BIOS, most of the notebook is F12 F11 F10 F2 What what, some computers may need to pay attention to press the FN key. All right = = In the restart interface disorderly press. After entering BIOS setup, close secure boot,secure boot must be turned off. Set up, the others are looking at the settings settings (the production of the USB stick is supported UEFI boot, set the USB boot as the preferred startup item), and then here must be saved in the exit Ah, the author here is the choice of exit saving chages. The following figure Baidu came, for reference. 5 Fifth Step, here to provide, boot boot options (General boot press f How many will see this, their own mess to try), which can not set the first USB disk boot disk and directly choose to boot from the U disk.6 Set up, can boot from the USB stick. (Will be a little computer knowledge above the basic itself has been solved.) After booting from the USB stick, enter a selection interface (if there are any read memory errors and then jump directly into the Linux GUI to indicate a problem with the BIOS setup, this is not sure if the installation is correct). After entering the selection interface, the first option is to go to the U Disk Linux live, directly inside the USB stick experience Linux without installing, the second option is to install Linux, the third self-view, if you choose the second option is to enter the GUI directly install Linux. However, the author here to choose the second option to install a problem, that is, after the division of the computer black screen, may be due to the problem of the graphics card. (Of course, some computers are a bundle of U disk to boot directly into the graphics system, if so please select the Chinese language, and then click on the trial with Ubuntu, each computer, each version of the system are different, but similar. So here we first enter the U Disk Linux system. Choose the first one, and after entering the system, everything will work. 7 is stuck in this interface! 8 In this step, we are going to start installing Linux on the computer, first click on the desktop to install Ubuntu (to ensure that the installation process is connected to the network, no network, I do not know what will happen.) A direct wired connection is generally used instead of PPPoE (broadband) or WLAN. (if there are many drive characters on the desktop, the right-click-unload) 9 Look at the picture, but these two steps are not the point. 10 This step is one of the main points, choose the other options, to create a mount point (mount point is the meaning of the partition) here is the heaviest point,,, installed dual system, here is a lot of partitions, you have to pay attention to the distinction, you split the 50GB here can be seen. Next we need to set up a number of partitions (mount point) (/boot,/,home,swap swap space,/usr, etc.) 1th set boot mount point, reference information as follows, is used to store system boot mount point, size 200MB or so, I divided 400MB. The 2nd set swap space swap, said straightforward point, hard disk with memory interactive space, virtual memory meaning. Set to twice times the size of a large memory. Set "/" mount point, size with you, the default directory, sub-8GB almost, 50GB please 10-15g set home/home user mount point, the size of 10GB, I set up here 5GB the rest of the space I gave to/usr, space, other suggestions are given a few GB (other include/ var etc on the main not mentioned), specifically what to use Baidu. Install boot launcher device select/boot corresponding to the SDA number, and then click on the following now install button can click Continue, dual system here formatting is not affect the windows inside things,Because the partition is divided. To make the relevant settings. Wait for a lengthy installation process. 11 to this step is almost complete installation, reboot will enter the GRUB2 boot interface, let you choose Windows Boot Management or Ubuntu. Of course, this is a long step and you need a few cups of coffee.
How to install WIN10 and Linux dual systems
