How to set up the tplink+ router

First, hardware connection

The WAN port, as shown in the following figure, is connected to a broadband feed, which is a network of computers connected to a LAN port.

Perhaps some of the netizens looked at the map, how to install the wireless router is still relatively confused, it does not matter, we provide two of the physical installation map, so that everyone on the wireless router installation no longer have questions.

From Router 1 to a line to the Router 2 WAN port, and then find a short network cable, a computer, a router 1/2/3/4 arbitrary interface, wiring mode as shown below:

Note: The Router 2 is in normal working condition because the LED SYS flashes, the WAN port is often bright or blinking, and the port that is connected to the computer in the 1/2/3/4 mouth is often bright or blinking. (after plugging in the power, the system LEDs are blinking after the router is working properly.) When the line is connected, the router's WAN port and the LAN port of the wired connection computer will be illuminated steady or blinking, if the corresponding port led is not bright or the computer's network card icon shows a red fork, then the line connection has a problem, try to check the network cable Connection or change the root cable to try. )

Second, establish the correct network connection

1, the Computer IP address settings

Right-click the "Network Neighborhood" icon on your desktop, select Properties, in the Open Network Connections page, right-click "Local Area Connection", select Properties, on the Open local Connection Properties page, select the Intelnet protocol (TCP/IP) Click Attribute, in the Intelnet Protocol (TCP /IP) Properties page, select "Automatically obtain IP address" and click OK.

2, the use of ping command to test connectivity with the router

In the Windows XP environment, click Start-Run, enter the "cmd" command in the running window that appears, return or click OK to enter the interface shown in the image below. (WIN7 system Click Start-Search programs and files-input cmd)

Input command: Ping 192.168.1.1, enter. If the screen appears as:

The computer has successfully established a connection with the router.

If the screen appears as:

This indicates that the device is not yet installed, please check the following order:

1, the hardware connection is correct?

The link/act LEDs for the corresponding LAN port on the router panel and the network card LEDs on the computer must be lit.

2, the computer's TCP/IP settings are correct?

If the IP address of the computer is the automatic acquisition method described earlier, you do not need to set it. If you set up IP manually, note that if the IP address of the router is 192.168.1.1, then the IP address of the computer must be 192.168.1.X (X is any integer between 2 and 254). The subnet mask must be set to 255.255.255.0, and the default gateway must be set to 192.168.1.1. Third, the router setup

After completing the above steps, we use the computer, open an IE browser window, enter the http://192.168.1.1 on the address bar to enter the configuration interface.

If 192.168.1.1 not open the user, please refer to the following prompts, according to their own situation to deal with

Please refer to the following methods for step-by-Step troubleshooting:

Method 1: The computer local connection is set to automatically obtain IP address; Please Baidu: How to change the computer's IP to automatic access?

Method 2: Broadband and router wiring connection error;

Telephone line access to the user: telephone line to the cat, the cat out of the line to connect the router's WAN port (blue interface), and then find a short network cable, one of our routers 1234 arbitrary interface (yellow interface), a computer;

Direct access to a network of users: directly behind your computer cable to our router's WAN port (blue interface), and then find a short network cable, one of our routers 1234 arbitrary interface (yellow interface), a computer;

Fiber-optic Broadband access users: Fiber-optic cat before connecting the computer network cable to the router's WAN port (blue interface), and then find a short network cable, one of our routers 1234 arbitrary interface (yellow interface), a computer;

Method 3: Replace the browser login router interface, note that the default login password is lowercase admin;

Method 4: In the case of the router power, long by the router interface reset small hole (button) about 10 seconds, you can reset;

Method 5: Manually set the local connection IP address: 192.168.0.X (1

Method 6: If you open the browser pop-up dial-up connection, click "Settings"-select "Never dial Connection"-"OK" and then log in again;

Method 7: If the browser pops out of work offline, open the browser to select "File"-Cancel "Work offline" before the tick;

then enter the corresponding account and password, generally new bought are admin

Account password Confirmation to enter the operating interface (generally are automatically bounce out)

You'll see a setup wizard on the left, go into

Click the Setup Wizard to show the following interface

We continue to click Next and appear as shown in the following figure

Access to the Internet to set up, we can see that there are three ways to choose the Internet, if your home is dial-up then use PPPoE. Dynamic IP general computer directly plugged into the network can be used, the upper layer has a DHCP server. Static IP is usually a special line or something, it may be the cell bandwidth, the upper layer does not have a DHCP server, or want to fixed IP. I chose PPPoE because I dialed. (PS: Ordinary home users are the choice of PPPoE, that is, ADSL virtual dial-up Internet)

Choose PPPoE dial-up Internet must fill in the Internet account and password, this should everyone understand that open broadband will have an account with, fill in the OK. (Need your broadband account password)

When the settings are complete, click Next, and you will see the basic wireless network parameter Settings page as shown in the following figure. We can see channels, patterns, security options, SSID, and so on, the general SSID is a name, you can easily fill in, and then the pattern is mostly 11bgn. Wireless security option we have to choose WPA-PSK/WPA2-PSK, so safe, so that people do not light the means to crack and rub the net. (Be sure to remember that you set the password, the password is lost in the security settings to modify, you can also choose to restart the router, repeat the above operation)

When the settings are complete, click Next, and the Setup Wizard, shown in the illustration below, will complete the interface and click Restart to make the wireless settings take effect.

Click to complete, the router will automatically restart, this time you wait patiently. The interface that appears after success.

To determine if the success has been set, we can use the following figure to understand

The basic setup of our Tp-link wireless router is complete after reboot.