HSRP (hot backup routing protocol between different VLANs)

HSRP650) this. width = 650; "border =" 0 "src =" http://www.bkjia.com/uploads/allimg/131227/1942135052-0.jpg "/>Vlan Division R6 (config-if) # switchport access vlan 10 R6 (config-if) # inter f1/2 R6 (config-if) # switchport access vlan 20 R6 (config) # interface range f1/3-4 Configuration R5> en R5 # conf t R5 (config) # vlan 10 Configuration address R5 (config-if) # no shut R5 (config) # inter vlan 10 R5 (config-if) # standby 2 ip 192.168.10.1 preemptible Configuration R5 (config-if) # standby 2 priority 150 configure vlan20 configuration preemptive permission R5 (config-if) # standby 3 priority 145 Server Load balancer % This switch is already the root of VLAN10 spanning tree VLAN 10 bridge priority set to 8192 VLAN 10 bridge max aging time unchanged at 20 VLAN 10 bridge hello time unchanged at 2 VLAN 10 bridge forward delay unchanged at 15 R5 (config) # spanning-tree vlan 20 root secondary VLANs 20 bridge priority set to 16384 VLAN 20 bridge max aging time unchanged at 20 VLAN 20 bridge hello time unchanged at 2 VLAN 20 bridge forward delay unchanged at 15 R5 (config) # inter f1/0 R5 (config-if) # no switchport R5 (config-if) # ip address 202.106.1.10 R5 (config-if) # ip address 202.106.1.10 255.255.255.0 R5 (config-if) # no shut R5 (config) # configure ip route 0.0.0.0 0.0.0.0 202.106.1.1 R3> en R3 # conf t R3 (config) # inte f1/1 for vlan Preemption R3 (config-if) # inter vlan 20 R3 (config-if) # ip address 192.168.20.11 255.255.255.0 R3 (config-if) # no shut R3 (config-if) # standby 3 ip 192.168.20.1 R3 (config-if) # standby 3 preempt R3 (config-if) # standby 3 priority 150 Server Load balancer VLAN 10 bridge priority set to 16384 VLAN 10 bridge max aging time unchanged at 20 VLAN 10 bridge hello time unchanged at 2 VLAN 10 bridge forward delay unchanged at 15 R3 (config) # spanning-tree vlan 20 root primary VLANs 20 bridge priority set to 8192 VLAN 20 bridge max aging time unchanged at 20 VLAN 20 bridge hello time unchanged at 2 VLAN 20 bridge forward delay unchanged at 15 R3 (config) # configure ip route 0.0.0.0 0.0.0.0 202.106.10.1: R4> en R4 # conf t R4 (config) # inter f0/0 R4 (config-if) # ip address 202.106.10.1 255.255.255.0 Test Result

<Span style = "font-family:; color: red; font-size: 14pt; mso-hansi-font-family:" Times New Roman '; mso-ascii-font-family: 'times New Roman '">

650) this. width = 650; "border =" 0 "src =" http://www.bkjia.com/uploads/allimg/131227/19421363K-1.jpg "/> 650) this. width = 650; "border =" 0 "src =" http://www.bkjia.com/uploads/allimg/131227/1942134049-2.jpg "/>

This article is from the "technical control" blog, please be sure to keep this source http://chenhao6.blog.51cto.com/6228054/1163724