Huawei vlan division, single-arm routing and Static Routing

Huawei vlan division, single-arm routing and Static Routing

Huawei vlan division, single-arm routing, and Static Routing allow all members to access the Internet
Huawei topology: IP address planning! Assign IP addresses to three computers
VLAN Division:

<Huawei> sy enters View Mode
[Huawei] un in en close message center
[Huawei] Change the switch name in sysname SW1
[SW1] inter vlan 1 enters the switch
[SW1-Vlanif1] ip address 192.168.0.10 24 with ip address
[SW1-Vlanif1] un shut Enabled
[SW1] vlan 2
[SW1-vlan2] vlan 3
[SW1-vlan3] vlan 4
[SW1] inter e0/0/2 inbound interface vlan Division
[SW1-Ethernet0/0/2] port link-type access
[SW1-Ethernet0/0/2] port default vlan 3
[SW1-Ethernet0/0/2] inter e0/0/1
[SW1-Ethernet0/0/1] port link-type access
[SW1-Ethernet0/0/1] port default vlan 2
[SW1-Ethernet0/0/1] inter e0/0/3
[SW1-Ethernet0/0/3] port link-type access
[SW1-Ethernet0/0/3] port default vlan 4
[SW1-Ethernet0/0/3] inter g0/0/1
[SW1-GigabitEthernet0/0/1] port link-type trunk set to medium port
[SW1-GigabitEthernet0/0/1] port trunk allow-pass vlan all
Set to pass all members

Single-arm routing:
<Huawei> sy enters View Mode
[Huawei] un in en close message center
[Huawei] Change the switch name in sysname R1
[R1] inter g0/0/0
[R1-GigabitEthernet0/0/0] un shut Enabled
[R1-GigabitEthernet0/0/0] inter g0/0/0.1 entering sub Interface
[R1-GigabitEthernet0/0/0.1] dot1q termination vid 1
[R1-GigabitEthernet0/0/0.1] ip address 192.168.0.1 24
[R1-GigabitEthernet0/0/0.1] un shut
[R1-GigabitEthernet0/0/0.1] inter g0/0/0.2
[R1-GigabitEthernet0/0/0.2] dot1q termination vid 2
[R1-GigabitEthernet0/0/0.2] ip address 192.168.1.1 24
[R1-GigabitEthernet0/0/0.2] un shut
[R1-GigabitEthernet0/0/0.2] inter g0/0/0.3
[R1-GigabitEthernet0/0/0.3] dot1q termination vid 3
[R1-GigabitEthernet0/0/0.3] ip address 192.168.2.10 24
[R1-GigabitEthernet0/0/0.3] un shut
[R1-GigabitEthernet0/0/0.3] inter g0/0/0.4
[R1-GigabitEthernet0/0/0.4] dot1q termination vid 4
[R1-GigabitEthernet0/0/0.4] ip address 192.168.3.10 24
[R1-GigabitEthernet0/0/0.4] un shut
[R1-GigabitEthernet0/0/0.4] inter g0/0/1
[R1-GigabitEthernet0/0/1] ip address 202.106.1.1 30 configure ip address
[R1-GigabitEthernet0/0/1] un shut
<Huawei> sys
[Huawei] un in en
[Huawei] sysname R2
[R2] inter g0/0/0
[R2-GigabitEthernet0/0/0] ip address 202.106.1.2 30
[R2-GigabitEthernet0/0/0] un shut
[R2-GigabitEthernet0/0/0] inter g0/0/1
[R2-GigabitEthernet0/0/1] ip address 202.106.1.5 30
[R2-GigabitEthernet0/0/1] un shut

<Huawei> sy
[Huawei] un in en
[Huawei] sysname R3
[R3] inter g0/0/0
[R3-GigabitEthernet0/0/0] ip address 202.106.1.6 30
[R3-GigabitEthernet0/0/0] un shut


Add a static route:
[R2] ip route-static 192.168.0.0 255.255.252.0 202.106.1.1 and then test the result
[R3] ip route-static 202.106.1.0 30 202.106.1.5
[R3] ip route-static 192.168.0.0 22 202.106.1.5
[R1] ip route-static 202.106.1.4 30 202.106.1.2
Test results !!!!!! All connected!