Install the Windows Server 2008r2 server operating system

Source: Internet
Author: User

R4900 G2 UEFI using RAID-1000 configuration array

Http://123.57.42.60/12755.html

First go into the array configuration interface in Uefi,

1Legacy BIOS mode enters the array card configuration interface

    • 2 Hard disk initialization
    • 3 Creating an array
    • 4 Switching the operating mode
    • 5 Deleting an array
    • 6 Select Boot Device
    • 7 Go to initialize

Server Restart Press ESC to enter the BIOS, select Advanced in PMC Maxview Storage manager-->scan for Controllers-->controller #0 pm8060-raid-- >logical Device configuration (Configure array).

The drive initialize drives (enabled) array is then initialized.

The cell array is then created to create array (enabled) arrays-->array type (RAID 1 (Mirror))-->proceed-->submit.

You can confirm that the array has been configured successfully by using the following interface (Logical Device configuration).

Manage Arrag-->defaultvalue0 RAID1 500gb-->logical Device configuration--enable (enabled)-->add.

Legacy BIOS mode enters the array card configuration interface

The server restart interface can be pressed CTRL + A into the array configuration interface. Then go to the array card configuration interface. Logical Device configuraction

2. Hard disk Initialization

The hard disk that needs to be configured for RAID must be initialized first, as follows:

Select Logical Device configuration--> Select Initialize drives--> press the "SPACEBAR" key to select the hard drive, the selected hard drive will appear on the right, enter confirm-and then the prompt will appear, Tells the initialization drive to erase all array information and enter Y to confirm.

3. Create an array

Select Logical Device Configuration First, then select Create Array, press "Space" to select the hard drive, the selected hard drive will appear on the right, enter confirm,

Then the raid specific parameters appear, check the desired RAID level, size, need to manually enter an array Label, select Done to create

Note Write caching recommends selecting the Enable with Backup Unit to avoid data loss when the power is lost, and after configuration is complete, the raid information can be confirmed by the following interface

4. Switch operation mode

Select Controller Settings--> Select Controller configuration--> which changes the Controller mode option, where the following options appear, enter to confirm

5. Deleting an array

Select Logical Device Configuration First, then select Manage Arrays, move to press DELETE, select the Delete option, select Yes to confirm

6. Select the boot device

Note This feature can only be seen in the mode that supports raw devices, and only the bare device (raw) can be selected

Select the logical device Configuration, select the Select Boot device, select the raw devices that need to be the Startup items, select the "Space", select the right side, and select Enter Y to confirm

7. Go to initialize

This option is not in Raid:hide raw mode

Select Logical Device Configuration, select Uninitialize Drives, press "Space" to select the hard drive, the selected hard drive will appear on the right side, there will be a warning, notify the initialization will delete the disk array information, select Y confirmation.

  

  

To configure the array method:

R4900 G2 UEFI uses RAID-1000 configuration array: http://123.57.42.60/12755.html

R4900 G2 Legacy BIOS RAID-1000 configuration array: http://123.57.42.60/12265.html

Load the array card driver installation system by following the link:

R4900 G2 UEFI Mode installs Windows R2 (RAID-1000): http://123.57.42.60/12611.html

Java plugins are required to use HDM, and if you cannot open the remote console, you need to add a Java site. Method: Http://123.57.42.60/11953.html

Array Card driver Link Location:

http://www.h3c.com/cn/Service/Software_Download/Server/Catalog/Rack_Server/H3C_R4900_G2/

Select the Raid2000 in the driver software, download the first link inside, and unzip the connection.

Windows Search: Drv-winser2008-adap.iso

If you are using HDM, the first image mounts the system image, and the second mirror mounts the array card driver: Drv-winser2008-adap.iso. If you want to use a USB stick to install also need to continue to unzip the Drv-winser2008-adap.iso, the inside of the files copied to the USB stick.

CentOS7.0: Download Linux_driver-54013.rar, unzip it, find linux_driver-54013 (1) \rel_2017_1_linux_driver_release_b54013\ Drv-rhel70-adap\x86_64, also if you want to use HDM mount, use Aacraid-driverdisk-1.2.1-54013-rhel7.0-x86_64.iso, if the USB flash drive to unzip it, the file is copied to the USB flash drive, If the hard drive is not found during installation, the array card driver installation needs to be loaded, and the command loaded is Linux DD. Method can refer to this URL: http://123.57.42.60/12435.html

Some of the configuration methods of R4900, this site is introduced, and HPE's server introduction, you can search by yourself.

Install the Windows Server 2008r2 server operating system

Related Article

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.