PS Rotating crystal Ball

Because the animated picture has 22 frames

So you can not make the picture more than 500*350 pixel

You can also use your imagination.

By the way,

As usual, the effect chart first

This picture is not transparent 50%

I gave out the design material.

You can also use your own

1, open the PS software, spread the material.

2, ctrl+j copy two layers, get layer 1 and Layer 1 copy.

3, in order to facilitate operation, first the background layer eyes off. Point Blueprint Layer 1, left hand hold shift, right hand with move tool to move layer 1 left some position, as shown above. Then click on the Blueprint Layer 1 copies, the left hand hold shift, right hand with the mobile tool to move the layer 1 copy right some position, as shown below.

Tips: When the operation should be careful not to keep pressing the shift first select the layer and then press the not selected layer to release

4, with the rectangular tool in the Layer 1 copy pull a rectangle (such as the dotted line in the above figure), feather 8 pixels, make sure that after the point of the keyboard press DELETE delete. The feather appears (pictured below).

5, point Blueprint Layer 1, with a rectangular tool and then the feather good dotted box (such as above) left, and then click the keyboard click Delete, as shown in the following figure.

6, the elimination of dashed box selection. Move the layer 1 and Layer 1 copies back to the seams by pressing SHIFT, and then use the left hand to press Shift-point blueprint Layer 1 and Layer 1 copies, as shown above, and merge two layers as layer 1 replicas, as shown above.

7, with an elliptical tool, point above (red box) in the column set "path", the left hand press shift, right hand with the mouse pull a positive circle, and then click on the map level version of the path, will appear in the Blue work path (shown below).

8, click on the map level version of the path to enter, the left hand press CTRL, right hand click Work Path, the original work path Blue is not (as above), at this time the circle into the ant line, then click on the surface version of the layer, and then back to the layer (pictured below). When you get back to the layer, the dotted box moves to the right place.

9, in the Layer 1 copy Panel "Add Layer Mask" (such as above), and then click on the Layer 1 copy panel on the figure and mask between the small chain (look at the red box below), remove the chain. Then put the background layer on the eye point.

10, click "Window-Animation" and open the animation panel, and then copy a frame (the middle and the following picture).

11, Dot layer 1 copy thumbnail, with the Move tool in the picture in the circular box of the image to the left to the right position, as shown in the figure above. Point back to the first frame (shown below), and then point to the small chain between the thumbnail and mask in the 1 copy of the layer. Finally, select the background layer.

Tips: Use the Move tool in the picture in a circular frame of the image to the left to not expose the end of the fit.

12, copy background layer to get a background copy, in the action Bar to perform "filter-blur-Gaussian Blur" command, a radius of 3.0 pixels, as shown above. Then merge the background and background copy layers.

Question: Why do you want to duplicate a layer? Because there are some words to be painted.

13, point Blueprint Layer 1 copy, click on "Transition Animation Frame" Transition 20 frames, as shown above and in the figure. Look at the animation effect, satisfied to click on the small black triangle above the animation panel, go in and click "Select All Frames", then click "Flatten frame to layer", and finally click "Delete Animation", as shown in the following figure.

14, "Flatten frame to layer", there are 22 frames. And then do an effect: the left hand presses CTRL, with the mouse click Layer 1 copy Mask to load the selection (see above), followed by the mouse point layer frame 1, perform the "filter-twist-Spherical" command, the value by default, determine (Do not cancel the selection), as shown in the middle two figure. Then click Blue Frame 2, open the eyes, the top of the menu "filter-twist-Spherical", and then point Blue Frame 3, open the eyes, the top of the menu "filter-twist-Spherical" ... So on, until you finish 22 frames (see chart below).

Friendly reminder: This place is to say that the left hand press CTRL, with the mouse click Layer 1 copy mask (that white circle) loaded into the constituency, I think we all know, there is no diagram. Immediately following the mouse point layer frame 1.

15, this part is very important. Do not cancel the selection. Create a transparent layer (see above), point menu "Select-Modify-Feather", feather radius of 8 pixels (see figure). Then click "Edit-Stroke", the stroke width is 5 pixels, and the position is "internal" (see figure three in the middle). Then click the Menu "select-Reverse" and click "Edit-delete" (see the Last picture).

16, transparent layer 1 reverse and delete, deselect, set the level version of the Opacity 50% (also can not set transparency). Create a layer of transparent layer, get transparent layer 2 (see above), use the Brush tool to find the soft corner in the brush preset on the menu, set the soft angle 100, and point to the top left of the ball as a light (see figure). Then click "Select-Select" On the menu, then reverse the ball, press the DELETE key on the keyboard to remove the light from the ball (see figure below).

Friendly reminder: The hardness of the brush drops to 0. In this way, the edges of the light appear soft and natural.

17, the Layer 2 cancel the selection (see above). Open the screen version, the layer of the 21-frame sphere eyes from top to bottom off, animation frame frame 1th, point layer frame 1 eyes (see figure). Add a frame, that is, the 2nd frame, open the sphere frame 2 eyes, add a frame, that is, the 3rd frame, open the sphere frame 3 eyes ... So on (see Figure 2), until 22 frames are finished, as shown in the following figure.

18, after watching the animation effect is satisfied, click the Web format, then click "Storage", as shown in the picture. The whole picture is complete.

Category:

• PS Getting Started Tutorial