Quick fast How do I set up a router (wired and wireless internet access)?

1, connect the router to the external network

Step one: Connect a good line

In the absence of a router, we are directly connected to the Internet through the computer to connect broadband, so now to use the router to share broadband Internet access, of course, the first to use the router to directly connect broadband. So the first thing we need to do is connect the lines, link the front-end broadband cable to the router (WAN Port), and then connect the computer to the router (LAN port), as shown below:

Attention matters

If your broadband is a direct network of households, directly to the front-end network cable plug into the router's WAN, the computer through a network cable to connect LAN mouth.

Physical wiring Diagram

After plugging in the power, the system LEDs (SYS light or pinion icon) are blinking when the router is working properly. When the line is connected, the LEDs for the router's WAN Port and the LAN Port of the wired computer will illuminated steady or flicker , If the corresponding port led is not lit or the computer's network card icon displays a red fork, it indicates that there is a problem with the line connection, try to check the network cable Connection or change the root cable to try. Please check: The cable is connected to the LED but does not light how to do?

Attention matters

L Broadband cable must be connected to the router's WAN port. The WAN port is different from the other four ports and is physically separated, and the computer is connected to any port numbered 1/2/3/4. Please be careful to confirm that if the line is wrong, it must not be on the net.

Step Two: Configure your computer.

Computers and routers need to communicate, so the first thing to do is to set up the computer. For most computers, the default does not need to do any settings, you can skip this step directly to step three, if you are unable to log in to the router management interface in step three, you can return to configure the computer's IP address.

Windows 2000/XP System:

Double-click the local connection "small computer" icon in the lower right corner of the computer desktop (if there is no network card icon in the lower right corner of the computer, enter the method as " start -- Control Panel -- network connection -- Double-click Local Area Connection "), and then follow the diagram below to configure it.

Windows 7/vista System:

Click on the network connection icon in the lower right corner of the desktop and click " Open Network and Sharing Center -- Change adapter Settings/ Manage Network Connections -- Right click Local Connection-- Properties " (or click " Start button-- Control Panel-- Network and internet-- Network and Sharing Center- Change adapter Settings/ Manage Network Connections-- Right-click Local connection- Properties "), and then follow the diagram below to configure it.

After the above configuration, your computer will automatically "Ask the router" IP address, routers will also receive the request after the allocation of parameters to the computer, after the success of the computer click on the lower right corner of the small computer icon, the local connection status of the "Support" tab can see the parameters of the computer, the following figure (XP system as an example):

Step three: Set up a router to surf the internet

① Open the Web browser, in the address bar input http://192.168.1.1 Open the management interface of the router, in the pop-up login box to enter the router's management account ( user name:admin Password: admin);

If you cannot open the management interface for your router, check that the IP address you entered is correct and that the "." The ending of the Chinese format. If you still can not log in please refer to: Not login Router management interface How to do?

② Select the " Setup Wizard " and click " next ";

③ Choose the right way to surf the internet (Common Internet has PPPoE, dynamic IP address, static IP address three kinds, according to the description below to choose the corresponding way of surfing);

PPPOE: dial-up Internet, stand-alone (not using a router) when using the Windows System to dial with a username and password. Is the most common way to access the Internet, ADSL line is generally the way the Internet.

PPPoE to enter a broadband username and password

Attention matters

L Many users can not access the network because of the input of the wrong username password, please carefully check the input of the broadband username and password is correct, pay attention to distinguish between Chinese and English input, letter case, suffix is full input.

Static IP Address: Operators provide you with an IP address, gateway, DNS, and so on, in some optical fiber circuits have applications.

Static IP to enter the operator to your IP address, gateway and other parameters

Dynamic IP: Operators tell you what also do not need to set, do not need to dial, also do not have to set IP address, etc. will be able to access the Internet, is the dynamic IP address online, in the community broadband, campus network and other environments will have applications.

Dynamic IP Direct point "next" on the line

④ set the wireless name and password (if it is a wired router, this step automatically skips):

The SSID, which is the wireless network name of the router, can be set by itself, and it is recommended to use an SSID with alphanumeric combinations. Select the Wireless security option, the password used to connect the wireless network input validation, can protect your router's wireless security, to prevent others from rubbing the net.

Set your own wireless name and wireless password, click "Next"

Attention matters

L Wireless name SSID is recommended to be set to a combination of letters or numbers, try not to use Chinese, special characters , to avoid some wireless clients do not support Chinese or special characters caused by the inability to connect. The FAST router defaults to the wireless signal name "Fast_ six hexadecimal characters" and is not encrypted, where the six-bit hexadecimal character is the last six digits of the router's MAC address, and the MAC address can be seen from the label on the bottom of the device. l To ensure your network security and network stability, it is recommended that you set up a wireless password to prevent others from illegally rubbing the net.

5 Setup Complete:

Enter the Admin interface (http://192.168.1.1) after reboot, open run state, wait 1-2 minutes, normally see WAN Port status at this time After the IP address of the specific parameters rather than 0.0.0.0, indicating that the router has been connected to the Internet at this time. If you see the parameter is 0.0.0.0, please refer to:Wan port status did not get the IP address how to do?

Step four: Try the computer to the Internet?

After viewing the router interface's WAN port has obtained the IP address, the computer may browse the webpage, the landing qq.

If you can login QQ, but not open the Web page, there may be a problem with the DNS parameters on the computer or the computer's browser settings, you can try to get the computer to regain the parameters (the computer network cable disconnected for 20 seconds or so) or switch to other browsers (such as Firefox, Google browser) try; If you still can't get on the net , see:Wan Port with IP address but not on the net how to do?

Attention matters

L After using the router, after setting the router with the parameters, the following computer can open the Web page directly, no longer use the "broadband connection" on the computer to dial .

Step five: How do other computers surf the internet?

Through the above operation, you are operating the computer will be able to surf the internet, but if there is a computer, how can you surf the Internet?

If you have a desktop, network TV and other wired devices want to surf the Internet, directly connect the device to the router's LAN 1/2/3/4 any idle port, and then follow the steps above the two configuration of the computer can be connected to the Internet, no need to configure the router.

If you have a notebook, iPad, mobile phone and other wireless devices to the Internet, please see the next section of the wireless settings.

2, wireless settings

Step one: Set up the router

Keep in mind that part 1th of step three is set in the router two parameters, one is the SSID Number (the name of the wireless signal), the other is the wireless security key (the first connection to the wireless signal need to enter the password).

Step two: Set up a wireless terminal

① sets the wireless signal for the computer to connect to the router.

If you want to use a computer to connect to the router wirelessly, first of all to ensure that your computer is equipped with a wireless card and work properly, for different operating system computers, its search and connection to the wireless signal method is as follows (wireless SSID to 0000 for example):

Windows XP System:

Double-click the Wireless network connection icon in the lower-right corner of the desktop, and then click Connect after selecting the router's wireless signal in the open signal list.

L Enter the previously set wireless password and click the Connect button (note Two input consistency and the case of the password).

Windows 7/vista System:

L Click on the Wireless network connection icon in the lower right corner of the desktop, select the router's wireless signal in the open signal list and click the Connect button. Then enter the previously set wireless password and click OK button.

② set up smartphones (for example, Android system) to connect the router's wireless signal.

L Click on the Phone's menu button and select System settings. Select WLAN in the Settings menu, turn on the WLAN switch, and select your wireless router signal name:

L Click on the wireless name to connect, enter the wireless password can connect successfully. If the wireless connection is successful but not on the network, you can refer to Figure 2, figure 3 below to specify the IP address of the mobile phone.

L③ set up iOS devices like ipad and iphone to connect router wireless signal

Open the ipad main interface, select the "Settings" menu and click Wi-Fi to enter the Wi-Fi network interface. Then turn on the Wi-Fi switch and click on your own router's wireless signal in the wireless network list.

L Enter your previously set wireless password and click Join. When the corresponding SSID in the wireless signal list shows "√", you can use the ipad to surf the Internet.

If you need to manually specify network parameters such as the IP address of the ipad, click the ">" button after the wireless SSID number in the wireless network list, and then click "Static" to manually set the ipad's network parameters.

Attention matters

If the wireless connection is set up after the discovery of wireless signals or search for signals but not connected to the phenomenon, please record the device system prompts the error message, and then search the network for the appropriate solution. You can also refer to: Do not search the wireless signal how to do? What about the signal but not the connection?

Step three: Try the wireless to the Internet?

Follow step two to connect your computer wirelessly to the router, and you'll be able to surf the Internet. If your computer has a "security prompt" message for the following page when you open the Web page, indicating that your wireless is not encrypted or that you have not chosen a secure encryption method, set wireless security as prompted by the page.

If the wireless device is unable to open the Web page after the wireless signal is connected, please refer to the wireless signal on the connection but not the Internet.

3. Frequently Asked Questions

The network cable is connected to the router corresponding led but does not light how to do?

L Check whether both ends of the network cable are connected to the correct port and plugged in;

L Check whether the device at both ends of the cable is powered on;

L try to change a new network cable;

L try to connect the device to another port on the router.

L Check to see if the SYS lamp for the router is normal and if the original power adapter is being used.

Can not log into the management interface of the router how to do?

L Check to connect the computer's router corresponds to the port LED is illuminated steady or flashing, if not bright, please refer to the cable connected to the corresponding led but do not light? for the investigation;

L Check whether the IP address obtained by the computer is in the same network segment as the router's IP address (the default is any number of 192.168.1.x,x 2-254), if different, please check the computer's network parameter configuration for errors according to the 1th part of step two;

L Unplug the router's WAN port, LAN1/2/3/4 port connection All other devices, only keep your computer, restart the router after the attempt to log in;

L Check Browser settings (click " Tools --internet options " In the browser, select the "Connection" tab, select " Never dial Connection " and click " LAN Settings ". Ensure that all three items are not checked in the state, click OK or change a browser (such as Firefox browser, Google browser) and then try again, if still can not manage, try to change a computer to visit.

L RESET the router to login again, reset method is: Under the state of the reset button (the reset button is generally the power socket or cable connector next to the small hole or the QSs button) after 10 seconds to let go, the router will automatically restart, and then again follow the steps in the article to connect.

What if the WAN port state does not get an IP address?

L Check the broadband connection router's WAN port led (Internet light) is illuminated steady or flashing, if not bright, please refer to the cable connected to the LED is not lit? for the investigation;

L Check the management interface of the "Running state--wan State" display of the way the Internet is correct, if not correct, please refer to the 1th part of the steps of the third reset;

If it is PPPoE dial-up, please check the "WAN status" prompts, the following figure, click "View Help", according to the relevant instructions (some routers do not have this prompt, please skip this step);

L Some service providers may bind the MAC address, please use the computer before the normal Internet, wired login to the router's management interface, select " network parameters --mac address Cloning ", click "Clone MAC Address", and then save, and restart the router according to the prompts, and then observe whether the router can obtain the IP address;

If the above operation does not solve the problem, please login to the router's management interface, select " System Tools - System log ", save the log and send to fae@fastcom.com.cn request technical support.

WAN Port with IP address but not on the net what to do?

If you can login to QQ but cannot open the Web page, it is most likely to get the DNS incorrect, open the " local connection state -- attribute --internet Protocol" ( TCP/IP ) -- Properties , manually fill in the DNS server address for 192.168.1.1 and 8.8.8.8. or contact the operator to consult the local DNS address, and then manually fill in;

• Manually specify the computer's IP address, gateway, and DNS parameters (as set out below), and then try to get back online;

L may be a computer browser or system problem, first try to check browser settings (Browser options " tool --internet option -- connection ", Select " Never dial Connection " and click " LAN Settings ". Ensure that all of the three items are not checked in the state, OK, save or change a browser (such as Firefox, Google browser) and then try again, if still not online, try to change a computer to access the network;

L Check your router for IP address filtering or MAC filtering, click " security Settings - firewall settings " or " Internet Control " in the router's admin interface. Open the firewall "or" Open the Internet Control "and then save, then try to open the Web page;

L try to connect broadband to the Internet, if it is not normal, please contact broadband operators.

What if you can't search for a wireless signal?

l See if the wireless card driver is successfully installed and enabled in Device Manager, or whether the computer can search for other wireless signals;

The method is as follows: Right click on the desktop " My Computer ", select " properties - - hardware - - Device Manager ", in the device list of the network adapter options , a green logo on the front of the network card indicates that the NIC driver is installed and enabled. If a red fork is displayed in front of the network card, it is not enabled, and right click on the network card select Enable. If the network card icon displays a question mark, an exclamation note, or a wireless card is not found, reinstall the NIC driver and reboot the computer.

L RECORD the contents of the corresponding error prompts on the operating system, and search the Internet according to the error prompts, and find the solution quickly;

If it is a notebook computer built-in wireless network card, please confirm the Wireless card switch has been opened (recommended to contact the computer manufacturer or inquire about the relevant instructions);

L Check whether the wireless service on the laptop is open;

The method is as follows (for example, in Windows XP): Right-click on the desktop " My Computer " and choose " Manage ". Select Services and Applications in Computer Management, and then locate and view the status of "Wireless Zero Configuration" on the Services page. Then right-click the property and click Start if the service status is not started. If the startup type appears disabled, change the startup type to Automatic, and then change the status to start again. (The way Vista and Windows 7 opens wireless services is similar to XP, except that its service name is "WLAN Auto Config").

L Check that the router's wireless LED is blinking normally, it is not normal to try to reboot the router or reset the router after the factory setting is restored;

L try to find out whether it is possible to search for your own wireless signal to avoid too many obstructions causing the signal to decay seriously. If you still cannot search for a wireless signal, try whether another computer or other wireless network card can connect to the wireless router. If not, please restore the router to the factory settings and reset the router or contact fast official technical support.

What about the signal but not the connection?

L record the error content of the operating system after unable to connect, and search the Internet according to the error prompts, and find the solution quickly.

L Click to refresh the wireless network, confirm whether to search the corresponding wireless network, and then try to connect;

L It is possible that the wireless password input is incorrect, please go to the Router management interface and open " Wireless settings - wireless security Settings " to confirm. Then try removing the wireless profile reconnect on your computer.

The Windows XP system clicks " Wireless Connection Status Properties - wireless network configuration - Preferred Network " (Windows 7 and Vista system entry methods are The Control Panel - Network and internet-- Management wireless network -Deletes the corresponding wireless profile. Then rescan the signal and connect.

L Check if the corresponding SSID for the router is Chinese or a special character, if you recommend that you change the SSID to save the letter and then restart the router and try to connect to the new wireless signal name;

L Change Method: Enter the router management interface, open " Wireless settings -- basic Settings ", re-enter the SSID;

L Check whether the wireless router has wireless MAC address filtering, use the network cable to connect the router into the management interface, and turn on " Wireless settings - wireless mac address filtering "To see if filtering is enabled. If enabled, please turn off filtering before attempting ;

L Login Router Management interface, open " Wireless settings - wireless security Settings ", choose not to open wireless security, and then save the restart after the attempt to connect;

If the wireless signal is still not successfully connected to the Internet, do not rule out the reason for the computer itself, please change a computer or other equipment to try.

Connect on the wireless signal but not on the net how to do (wired to the Internet)?

L refer to Step two of part 1th to reset the computer, modify the Internet Protocol properties of the wireless network connection (not the local connection) , set to "get automatically", or change the automatic get IP to manually specify the network parameters of the computer.

L Check if you have IP address filtering or MAC filtering in your router, click " Security Settings - firewall settings " or " Internet control " in the router's admin interface, and uncheck "Open the Firewall" or "Turn on the Internet control" and then save, then try to open the Web page;

l DISABLE the local connection of the wired network card on the computer and any other connections other than the wireless network connection, and try again ( right click on the desktop Network connection and select Properties );

L may be a computer browser or system problem, first try to check browser settings (browser options tool --internet option -- connection ", select" From no dial-up connection , click LAN Settings . Ensure that all of the three items are not checked in the state, OK, save or change a browser (such as Firefox, Google browser) and then try again, if still not online, try to change a computer to access the network;