Router installation set up detailed operation detailed

Home network equipment with the development of the network also presents a rapid change, then how to do a good job in the router installation settings? This is our first step to achieve the Web surfing, then the following to the detailed introduction of a router installation settings for the specific operation.





Router installation Setup implementation process:





Router installation settings 1





typically also has 4-port 10/100m switches embedded, which are simple to install. When you apply for a broadband connection, the ISP will install the line for you, you only need to connect the incoming line (the network cable or Adslmodem LAN port) to the router's WAN (WAN) interface, and then connect the router's LAN (LAN) interface to the hub, switch or computer network card.





Router installation settings 2





routers support commonly used three kinds of settings: PPPOE, dynamic IP, static IP. Routers are typically web-based management pages, and for users who have no experience with routers, products are generally equipped with very detailed instructions to help users understand the use and configuration of routers. We can use the Setup Wizard prompts to easily complete the configuration.





we need to know the relevant parameters to the ISP (Network service carrier): If the static IP mode, please understand the following parameters: Static IP address, subnet mask, gateway, DNS server, alternate DNS server. If the dynamic IP mode: To get the IP address from the bureau, if you need to manually set the DNS server address, please consult your ISP. If this is a PPPoE method, please know the following parameters: Username, password.





Router installation settings 3





in IE or other browsers to enter the router address in the manual, enter the user name and password to enter the router's control interface. Newly bought equipment, in the manual will have the address and user name password description, according to the above is completed, the general IP address is 192.168.1.1, subnet mask is 255.255.255.0, username and password are: admin.





4, we get the accurate parameter information, after entering the router Setup interface, follow the instructions on the Installation Wizard, fill in the corresponding parameters, you can complete the setup. Generally speaking. At this time we should be able to surf the internet, but the actual situation is not the case, this is because of the router MAC address problem, we only need to find the MAC address cloning options, select the Clone MAC address, after saving can be online.





Router installation settings related advanced operations:





in the application of router installation settings, there are many settings skills, although it is not difficult, but it can play a big role in our internet life.





on-Demand connection:





the state of the WAN Port PPPoE mode, there are 4 options on-demand connection. On-Demand connection: Automatically connect when there is access to data. Automatic connection: Automatic connection after power-on and disconnection. Timed connection: The connection is automatically made within the specified time. Manual connection: Manually connected by the user. Note that the factory defaults to the first item, that is, 15 minutes without detection of packet transmission, will be automatically disconnected.





Packet filtering:





Controls access to computers in the local area network by filtering packets, such as setting up some computers that can only send and receive mail, but cannot access the Internet. Set up method: Security Settings-Firewall settings-fill in the information you need to control your computer, such as effective time, LAN IP address, port, WAN IP address, port, protocol, and so on.





Domain name filter settings:





to the local area network of computer access to some sites to control, can ensure a healthy internet environment, to avoid browsing bad websites. Setting method: Security Settings--Domain name filter, fill in the effective time, domain name and other information.





Internet time settings:





on the Internet time limit, easy to achieve docking into the management of user hours. Setting method: Security Settings-Firewall Setup Wizard, fill in the time period that prohibit the Internet, can control the machine of the local area network cannot visit the Internet during this period





MAC address filtering settings:





By filtering the MAC address to control the access rights of computers in the local area network, you can easily implement this setting if you do not want to allow some users to surf the Internet. Its router installation method: Security settings--mac address filtering, fill in the need to filter the MAC address.





Virtual server settings:





defines the mapping relationship between a WAN service port and a LAN server, and easily builds a Web server, an FTP server. Set method: Forwarding rule--Virtual server, fill in the corresponding server port and the server's IP address.





DMZ host settings:




The
DMZ host makes a particular computer open to the Internet, and some applications require multiple TCP/IP interfaces to be opened, and the DMZ can implement these functions for the computer. Typically, only one DMZ host can be supported at the same time. Set method: Forwarding Rule--DMZ host, fill in the corresponding computer IP address.





View Router running status:





can easily get to know the router's LAN port, Wan port status, and traffic statistics. Viewing method: Router Settings page--run state.





above is the home router setting method, although not particularly detailed, also impossible to do everything, but I believe that the home user through this article, or can master some settings, there are more functions, this requires everyone in peacetime when the application to find summed up.





router installation settings related to the introduction to you here, I hope that you understand and master the installation of the router's relevant operational details to help.