Port image configuration in DELL
InVswitchChoose "Switch"> "Ports"> "portinging" from the tree menu on the left of the management interface"Port Image), The "portinging" port image is displayed on the right. The parameters on this page are described as follows:
Add): Add a port Image
DestinationPort destination port): defines the port number for port communication to be mirrored;
SourcePort source port): defines the port number of the mirrored port. Up to eight mirrored ports can be mirrored to one mirror port;
Type): Specifies the port communication Type to be mirrored. Possible field values include "RX"-indicates the data from the image to the network; "TX"-indicates the data from the image to the network; and Both)-indicates all the data from the image.
Status): indicates the port Status. Possible field values include: "Active"-indicates that the port is enabled; "NotActive"-indicates that the port is disabled.
Remove delete): deletes a port image session. Possible field values include: "selected"-delete port image session; "not selected"-retain port image session.
Specific port image Configuration:
1. Select the destination port image from DestinationPort in the portconfiguring dialog box), and then click the Add button;
2. on the "AddSourcePort" add source port) page, define the "SourcePort" source port) and "Type" fields, and click "ApplyChanges" to apply changes ), allows the system to receive changes.
Note: To delete a copy port from a port image session, open the "portinging" port image) page, select the "Remove" delete) check box, and then click "ApplyChanges" to apply changes ). The system will delete the port image session and update the device .)
The following is a CLI command instance:
- Console(config)#interfaceethernet1/e1
-
- Console(config-if)#portmonitor1/e8
-
- Console#showportsmonitor
-
- SourceportDestinationPortTypeStatus
-
- ---------------------------------------
-
- 1/e11/e8RX,TXActive
Next, let's take a look at how Port Mirroring is configured for several types of switches:
How to configure the port image of the Juniper Switch
How to configure the port image of the JuniperM series and T series switches
Usen @ router # showforwarding-optionsport-loading ing {input {familyinet; rate; run-length ;}outputinterface {next-hop;} no-filter-check ;}}
Select the destination port to which the sampled traffic is sent.
User @ router # showfirewallfiltermirror-samplefrom {...} then {sample; accept ;}
Define a sampling filter and select the traffic you are interested in.
User @ router # showinterfaceunit0familyinetfilter {inputmirror-sample ;}
Select to apply the sampling filter to a port.
How to configure the port image of the Nortel8000 Switch
In versions earlier than Software3.2.0.0, a set of port images, 10 sources, and one destination are supported.
Software3.2.0.0 and later versions support two sets of images. Note: Generally, eight ethernet ports are used as an integrated circuit board. destination cannot be deployed on the same board, only one destination is allowed on Ports 1-8), and 25 sources are supported.
Username/password: rwa/rwa superuser
For example: 2/62/62/8 images to 2/1 Images
- Configdiagmirror-by-port1createin-port2/4out-port2/1 (1 is ID, range 1-10)
-
- Configdiagmirror-by-port1enableture
-
- Configdiagmirror-by-port2createin-port2/6out-port2/1
-
- Configdiagmirror-by-port2enableture
-
- Configdiagmirror-by-port3createin-port2/8out-port2/1
-
- Configdiagmirror-by-port3enableture
-
- Configdiagmirror-by-port1modeboth | tx | rx
-
- Saveconfig
-
- Diagmirror-by-portidinfo (view ID No. Image Information)
The image function provided by the Nortel switch is generally rx and does not support the both method depending on the cpu). Therefore, if the ping packet fails to be detected, only ping can be detected .?
How to configure the port image of the Baystack450 Switch
Veryeasy, as long as the installation menu step by step. Only two sources and one destination are supported. Vswitch Software Version 3 or later.
- Ssr8000
-
- SSRCommandLineInterfaceReferenceManual551
-
- portmirroring
-
- Command
-
- Purpose
-
- ApplyportmirroringtooneormoretargetportsonanSSRortotrafficspecifiedbyan
-
- ACLprofile.
-
- Format
-
- portmirroringmonitor-porttarget-port|target-profilename>
-
- Mode
-
- Configure
-
- Description
-
- Theportmirroringcommandallowsyoutomonitorviaasingleporttheactivityofone
-
- ormoreportsonanSSRorthetrafficthatisspecifiedbyanACL.
-
- Parameters
-
- monitor-port
-
- Theportyouwillusetomonitoractivity.
-
- target-port
-
- Theport(s)forwhichyouwanttomonitoractivity.Youcanspecifyasingleportora
-
- comma-separatedlistofports.
-
- target-profile
-
- ThenameoftheACLthatspecifiestheprofileofthetrafficthatyouwantto
-
- monitor.TheACLmustbeapreviouslycreatedIPACL.TheACLmaycontain
-
- eitherpermitordenykeywords.Theportmirroringcommandonlylooksatthe
-
- followingACLruleparametervalues:protocol,sourceIPaddress,destinationIP
-
- address,sourceport,destinationport,andTOS.
A port image is a classic vswitch configuration process. The above lists the port image configuration instances of several common vswitch brands and models, of course, you can read the following articles to learn about the most common configurations of Huawei and CISCO switches.