Users connected by telephone lines(Prepare two short network cables)
Connect the telephone line (the finer line) to the line port of the Cat (the smaller one). The Cat splits a network cable into the WAN port of the router and finds a shorter one.
Network cable, one connection to the computer, one connection to any interface of vrouters 1/2/3/4, the wiring method is as follows:
Note: the normal working status of the router is SYS flashing, the WAN port is always on or flashing, and the port connecting to the computer in the 1/2/3/4 port is always on or flashing.
Users who directly access the network cable(Prepare two short network cables)
Connect the incoming network cable to the WAN port of the router, find a short network cable, connect to the computer, and connect to any interface of vro 1/2/3/4. The wiring is as follows:
Note: the normal working status of the router is SYS flashing, the WAN port is always on or flashing, and the port connecting to the computer in the 1/2/3/4 port is always on or flashing.
Set the local connection IP address on the computer to"
Automatically obtain the IP address"
<Click this link to obtain the ip address automatically in Win7
1. Right-click"
Network neighbors", Select"
Attribute":
2. Click"
Local connection", Select"
Attribute":
3. Double-click"
Internet Protocol (TCP/IP)":
4. Select"
Automatically obtain the IP address""
Automatically obtain the DNS server address", OK:
1. Enter:
192.168.0.1Press enter and enter the password on the jump page.
AdminClick"
OK"
<192.168.0.1 cannot be opened? Click this link
2. Select"
ADSL dialing", Enter the bandwidth account and password,"
OKAs follows:
If the WAN port status shows"
Connected", You can browse the web page and surf the Internet.
Tip: After you access the Internet through a vro normally, you do not need to click "broadband connection". You can directly access the Internet at startup. If other computers need to access the internet
Network, directly connect the computer to any idle interface of vro1234, refer to step 2 to change the local connection to automatically get the ip address, no need to configure the router.
After the vro settings are complete, the network cannot be connected.
After vro configuration is complete, the network cannot be connected. What should I do?
You can go to the vro settings page (192.168.0.1) and click"
Advanced Settings"-"
System Status"According to the connection displayed on the WAN port
Status to determine your own problems.
There are three connection statuses:
Question 1: What should I do if "connection in progress" is displayed?
Question 2: What should I do if "not connected" is displayed?
Question 3: What should I do if "connected" is displayed?
Question 1: What should I do if "connection in progress" is displayed?
Cause 1: The Internet access method of the WAN port of the router is incorrect.
Solution: go to the vro settings page and click "Advanced Settings"-"WAN port settings" to select the correct method for accessing the Internet. > How do I select the Internet access mode?
Cause 2: The bandwidth account and password are incorrect or case insensitive.
Solution: enter the correct broadband account and password. Make sure that the password is case sensitive.
Cause 3: When the access method is automatically obtained, the IP address obtained by The WAN port of the router conflicts with the IP address of the LAN port of the router.
Solution: modify the LAN port address of the router. > How do I modify the LAN port address?
Cause 4: The network broadband operator binds the bandwidth account to the MAC address of the computer.
Solution: Clone the MAC address on a computer that does not connect to the vro and can access the internet normally.
Cause 5: The drive capacity is insufficient due to the long broadband lines in the household.
Solution: change the WAN port speed of the router to 10 Mbit/s full duplex.
Question 2: What should I do if "not connected" is displayed?
Cause 1: Line connection error (the WAN port is not wired or the network cable to be connected to the WAN port is connected to the LAN port by mistake)
Solution: Check whether the two ends of the network cable are connected to the correct port and plug in (after the line is correctly connected, the WAN port indicator on the router should always be on or flashing ).
Cause 2: Poor or damaged network cable quality
Solution: replace a new network cable (ensure it is good ).
Cause 3: Insufficient driver capability
Solution: change the WAN port speed to 10 m full duplex. ?
Question 3: "connected" is displayed but cannot access the internet. What should I do?
Cause 1: The Internet access method in the vro is incorrect.
Solution: go to the vro settings page 192.168.0.1 and click "Advanced Settings"-"WAN port settings"-select the correct method for accessing the Internet. > How do I select the Internet access mode?
Cause 2: The IP address of the computer is not automatically obtained.
Solution: change the IP address of the computer to automatically get it. > How do I change the ip address of my computer to automatic retrieval?
Cause 3: The computer's domain name server error (dns) (Can QQ, cannot open the web page)
Solution: manually specify the local connection DNS as 8.8.8.8. > How do I specify a dns address for my computer?
