Vios multi-VLAN Setup

Fix after "Go" test

Successfully let IVM run a number of VLANs, add a can carry multiple Vlanid network card, Nativevlan is the compromise method of transformation, if not like this method, with---Delete multi-vlan Nic method, in general, Lpar can only and IVM in the same network segment, I have a study, Success has allowed IVM to run multiple VLANs. The steps are as follows: first, change the blade's built-in switch settings to find the appropriate interface for the blade Interfacegigabitethernet0/10switchporttrunk

In general, the Lpar can only and IVM in the same network segment, I have a study, successfully let IVM run a number of VLANs. The steps are as follows:

First, change the blade's built-in switch settings to find the appropriate interface for the blade

Interface GIGABITETHERNET0/10

Switchport Trunk Native VLAN 500

Switchport trunk allowed VLAN 100,200,300,400

Switchport mode Trunk

The interface mode is changed to trunk, note here that the native Vlan,native VLAN is selected as the VLAN ID of the Vios with the network segment, for reasons later said.

At this time the Vios IVM will break for more than 10 seconds, after resuming the next

Telnet to PS701 Blade

Add a network card that can carry multiple VLAN IDs, and try to predefine all the VLANs you want to use, once the device is used, it cannot be changed dynamically.

$ chhwres-r Virtualio--rsubtype eth-o a--id 1-s 100-a

Port_vlan_id=5,ieee_virtual_eth=1,\ "Addl_vlan_ids=100,200,300,400\", Is_trunk=1,trunk_priority=1

Bridge the newly added NIC to the physical interface of the blade

# LSDEV-CC Adapter

Ent0 Available Logical Host Ethernet Port (Lp-hea)

Ent1 Available Logical Host Ethernet Port (Lp-hea)

Ent2 Available 04-00 2-port Gigabit Ethernet pci-express Combo Adapter

(e4143a161410a003)

Ent3 Available 04-01 2-port Gigabit Ethernet pci-express Combo Adapter

(e4143a161410a003)

ENT4 Available Virtual I/O Ethernet Adapter (L-lan)

ENT5 Available Virtual I/O Ethernet Adapter (L-lan)

ENT6 Available Virtual I/O Ethernet Adapter (L-lan)

ENT7 Available Virtual I/O Ethernet Adapter (L-lan)

Ent8 Available Virtual I/O Ethernet Adapter (L-lan)

Ent9 Available Shared Ethernet Adapter

Then the system will be more than a sea card

In the Lpar properties, change the NIC settings, select the VLAN ID number you want to run, and if you want the same network segment as the Vios, select the native VLAN option

Native VLAN is a compromise method of transformation, to ensure that the Vios IVM itself out of the data frame to communicate with the outside world, if you do not like this method, you can telnet to the Vios, configure the network card to carry the specified VLAN ID, the switch side to remove the Native VLAN.

Attached---Remove the multi-VLAN Nic method, note that the blade's serial number is written to:

First, all bridges are removed, run

$ chhwres-m server-8406-70y-snxxxxxxx-p xx-xxxxx-r virtualio--rsubtype eth-s 100-o R

/usr/ios/lpm/sbin/lpmdrmgr drmgr-c slot-s ' u8406.70y.xxxxxx-v1-c100 '-r

u8406.70y.xxxxxxx-v1-c100

Vios multi-VLAN Setup