A machine novel good to do how to replace the ipad front panel

If your ipad doesn't have a warranty and you don't want to buy a new one when the panel is damaged, then you need to learn the following tutorials. (Reference equipment: iPad2, Newipad) preparatory work 1. It's best to know what you need to do to fix a smartphone or tablet, which will help you determine whether you're fixing your ipad or sending the ipad to a repair shop. 2. Parts: A home key and camera bracket (can be taken from the old front cover), a new front plate (can be purchased online, the price between 50 dollars to 150 U.S. dollars), adhesive tape (double-sided adhesive) 3. Tools: Hair dryer (or hot air), thin metal blades, a number of multi-functional tool pens, A number of guitar dials (or plastic opening tools), Phillips No. 00 screwdriver. In the tutorial, a iPad2 is used as the experimental material, and the same method can be applied to the Newipad front panel. It should be pointed out that the user should bear the risk of damage, destruction and data loss during the repair of the equipment. I believe you will experience a lot of fun in the repair process, words do not say more quickly to learn! 1. Backup data to prevent accidental loss of ipad data during repairs, you can upload all the data from the ipad to the icloud cloud storage server or itunes. 2. Uninstall the damaged front panel when the first step is completed, heat the edge of the front panel with a hairdryer (or hot air) to quickly dissolve the adhesive between the front panel and the ipad body. Until you can easily insert a thin sheet into the front plate and the body of the glue, then stop heating, and then carefully separate them. If the front panel and fuselage are still very difficult to separate, then continue to heat the area, do not be reckless. Also, be careful not to insert the tool too deep to prevent damage to the screen panel and other internal parts. After separating the front cover from the fuselage, you need to put a fixture (a plastic multi-function tool or a guitar flap) in the middle to prevent the separate front panels from being glued together. You also need to be very careful when you remove the home key. Wi-Fi antennas are built into the front panel, just around the home button, and you have to carefully separate them. Note the lower left corner of the front panel. The cable of the digital converter is right there, don't be reckless to rip them out, which can damage other built-in parts. After completing the separation of the fuselage from the front panel, you have to remove the latter from the ipad board. Unfortunately, the nuts that connect them are underneath the screen panel. So you have to first wring out the four Phillips screws on the screen, and then, when you're done, gently tilt the screen panel from the motherboard in the right to left order. Then, take the nut out of the screen panel and put the screen panel properly. Now, the front panel is finally separated. Slowly pry the two locking lever on the digital converter cable away, and then gently detach it from the motherboard's metal cover while pulling the ribbon cable plug. 3. Remove the Home key andAfter the camera lens separates the damaged front panel from the host, the home key is removed from the former panel with a Phillips screwdriver. Now you need to use the hair dryer again, heat the bracket and the button while separating them. Similarly, when you remove a camera lens, you need to heat it first and then separate it from the front panel with a thin blade. 4. Install the home button on the new front panel and the camera with a prepackaged adhesive tape (or double-sided adhesive) to secure the camera on the new front panel. When you install the home key and the key bracket, repeat the same steps, and then use a screwdriver to fix the home key two times. 5. Install the new front panel before installing the new front panel, the residual adhesive tape and broken glass must be removed from the host. When you are finished, reconnect the digital converter cable and the motherboard and fix it with the lock lever. Reinstall the screen panel and fasten it to the machine with the nut. Then, reset and fix the front panel of the chassis to ensure that the cables are not damaged in the process. Next, do not rush to use adhesive tape to glue the front plate and the fuselage, you should first check whether the front panel is installed in place, the ipad can be normal operation. After the first steps are correct, the machine is closed, then the front plate and the fuselage are bonded with the adhesive tape. Need to be reminded that before the front panel adhesion, it is best to carefully check the screen panel and the inside of the panel is dust and other impurities. If so, remove it with a fiber cloth or jet sac. Try not to contact the front panel's imaging area or screen panel directly with your hands, let alone touch other fragile areas. After determining the front panel and screen panel are bright clean as new, then the former fixed to the machine, and gently press with the hand, pay attention to the fuselage with four corners of the alignment. Finally, the front panel of the protective film is torn down (if any), the front panels to replace the completion of the. Although the replacement process is cumbersome, but after the completion, your ipad looks like a new one?