Thanks for the hard work, we finally finished the NFS network.
First, the computer and the Development Board need to be connected to the router to form a LAN (I ignored this ...)
PC: Ubuntu 12.04
Development Board: Linux 2.6.32.2 click to view Ubuntu to burn Linux TO THE DEVELOPMEN
In the previous article http://www.cnblogs.com/linzizhang/p/4817336.html introduced the first part of the system software on the Development Board--bootloader the compilation method.Background: After the bootloader is burned into the NAND flash of the Development Board, the Develop
Objective:Recently in the use of OK6410 Development Board running Linux system, often on the terminal to knock some instructions, but the Development Board screen is too small to use it very inconvenient, so the use of a terminal can run in the software on Windows is connected to the
Address: http://blog.csdn.net/ipromiseu/article/details/5154004
Detailed solution for 3G cards on the Development Board (applicable to most 3g cards)
Anson Luo/gray Luo (Luo Guohui)
I. Environment
1.Development Board kernel: Linux kernel 2.6.14
2.3G card: Huawei e1750
2. Download related tools and library files
1. usb
The arm Development Board is essentially a small computer system. Therefore, you can compare the Learning Development Board with a PC computer.
A new computer needs to be installed with a system (pre-installed by the manufacturer or installed by yourself) before it can be used. In the same way, the
These two days want to try the TFTP download function under the Uboot, so to establish the Development Board and Ubuntu Network connection, encountered some problems in the middle, is recorded, lest forget.
1. At the beginning, whether the PC Ping Development Board or the Developme
to use, provided that you can get more than one address. It is not suitable for anyone who wants to conduct various network experiments, because you cannot control the network of the virtual machine and it goes out directly. The schematic diagram is as follows:
2: After installing VMware and Red Hat (remember to install the NFS installation package), configure the Linux network. Because the IP address of my Development
Because the ARM architecture Development Board can be based on the X86 architecture of the PC on the CPU instruction and the binary is different, and if the Linux driver needs to access the hardware, these hardware is difficult to simulate on the PC, so we need to debug and test on the Development Board with these hard
Configuration of tftp server in ubuntu 10.04 and use of tftp commands on the Development Board tftp server in ubuntu 10.04: Step 4: install the software required for tftp. First, install tftp-hpa and tftpd-hpa. The former is the client and the latter is the service program. Enter sudo apt-get install tftp-hpa tftpd-hpa on the terminal, install tftp-hpa and tftpd-hpa. Then you need to install xinetd, enter s
How do I practice writing drivers and developing BSP after I buy a development board? (Author: wogoyixikexie @ gliet)
How do I practice writing drivers and developing BSP after I buy a development board? (Author: wogoyixikexie @ gliet)
---------- A newcomer asked questions at the csdn Forum
Recently I want to buy a 244
The 5th chapter: Build the test environment of s3c6410 Development BoardThis chapter mainly introduces the Android system installed on the OK6410 Development Board developed on the basis of Samsung's launch of the s3c6410 Development Board.Install serial debugging tool: Minicom1th Step: Detect whether the current syste
This article goes from WebEx to:http://www.topeetboard.comVideo explanation Address:http://v.youku.com/v_show/id_XOTI4Njc0NDIw.htmlKnowledge system of embedded technology: Learning steps for the iTOP-4412 Development Board and accompanying tutorialsEmbedded knowledge of a wide range of beginners difficult to get startedThis section describes the embedded technology learning steps for beginnersTry to play th
Tianyinxing technology company will launch the latest development board of cortex-a8 series in the National Day -- tq210v6 Embedded Development Board. the core board parameters of tq210v6 have been announced ahead of schedule. Now, we have released comprehensive baseboard pa
For Rongping 4412 Development Board use of related issues, for reference only.Note: RP4412 Development Board Upgrade burn write to inand boot must press the power button about 5S.Q: With the Rong product Samsung Exynos4412 Development Bo
In front of the transplant work has been done, the use of the arm Development Board is Guangzhou REAL210 (V6.2) Development Board Android versionHere is a brief introduction to this development Board:1. Software Features1.1 Bootlo
The development Board is a relatively complex electronic system, please be patient and assemble in accordance with the instructions in this chapter, so as not to cause unnecessary loss.It is best to use the cable provided by Schindler, as some parts are specifically customized and may be purchased on the marketConnector lines and parts do not match, unauthorized use of the wiring or parts purchased on the m
cardJust modified the original u-boot.bin to uboot_sd.bin, because the uboot compilation script MK also made the corresponding changes.
Step 7: Use fastboot to burn the image file to the SD cardLinux fastboot for Android source package compiled, the specific path is Android/out/host/linux-x86/bin directory. Therefore, firstYou need to modify the Ubuntu environment variable script:Vim/etc/bash. bashrcAdd the following statement:Export Path =/opt/arm-2009q3/bin: $ pathExport Path =/home/lqm/s5pv2
problem Description:Stm32 provides a number of IC entry-level development boards, the price is quite cheap. Stm32f0308-discovery is an entry-level Development Board for the CORTEX-M0 architecture. The following is a brief introduction to it.io Convenient:? As long as a USB cable is connected to the PC for development,
After I got the OK2440 Development Board, I got the development board yesterday after connecting to the nfs server. After I clicked it, I found that the LCD was really bad. No money is required. Ke, I entered the topic. Today, I tried to connect to the company's computer with the D
the command " vi arch/arm/mach-exynos/mach-itop4412.c" to open the mach-itop4412.c, As shown in the following:then find the " struct platform_device s3c_device_buzzer_ctl " line, as shown in:Change the " #ifdef config_buzzer_ctl"in front of this line to "#if defined (config_buzzer_ctl) | |Defined (config_buzzer_ctl_module) "as shown in:then find the " s3c_device_buzzer_ctl" line, as shown in:Change the " #ifdef config_buzzer_ctl"in front of this line to "#if defined (config_buzzer_ctl) | |D
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.