broadcom router

First, make sure you are a bit ldquo; Lucky Winner rdquo;:/sbin/lspci | grepBroadcom0b: network00.0 controller: broadcomconfigurationbcm4312802.11a/B/g (rev01) install the required components: First, make sure you are the lucky guy with the Broadcom BCM43xx wireless network card ": /Sbin/lspci | grep Broadcom 0b: 00.0 Network controller: Broadcom C

First, installed under UbuntuThis does not have to be installed, the system is well supported.System->administration->hardware DriversChoose the Broadcom STA wireless driverActivateIf you do not have this option, execute it in the shell:sudo apt-get updatesudo apt-get--reinstall install bcmwl-kernel-sourceAfter restarting, repeat the previous step to activate the driver. I tested the Chinese version of Ubuntu14.04 and found that this driver was not in

Source: qiuyi21.cnblogs.com1 , download the latest official version of the driverOn Broadcom official website http://www.broadcom.com/support/ethernet_nic/downloaddrivers.php Download the latest official version of the driver for your network card, do not download the beta version.2 , delete the system's own driver cacheAt the same time press the WIN + x appear management menu, then press g Key to open Computer Management, left check "Device Manager",

Provides its own message mechanism in Broadcom, with two message forms: Request/response and Event(event)request/response Message: the communication between the process is through the SMD, all the messages are sent to the SMD,SMD after receiving the information, if the message is to be SMD to do the corresponding operation, if not, the message route outEvent messages: a process that is interested in certain events can cms_msg_register_event_interest r

The configuration of the broadcom wireless network card under Debian4.0r0-Linux Release Technology-Debian information. The following is a detailed description. It should be said that debian has evolved to 4.0r0, and his desktop system has become perfect. I had been using Ubuntu 6 since 3.3, but it was intolerable, but now it turns back and finds that 4.0r0 and ubuntu have no special difference and are more stable. I often encounter conflicts and error

First, the configuration of the port group in the actual situation of the use of many scenarios, partial redundancy mainly to solve the single point of failure. Many are in combination with Ha, VRRP, HSRP, switch stacking and many other practical scenarios.All right, no nagging, just "meal".The first step:Configuration Broadcom NIC Group to broadcom network card Group is enabled on the NIC, need to be inst

Debian drive Broadcom Series wireless cards 4311, 4312, 4313, 4321, 4322, 43224, 43225, 43227, 43228 The drive configuration process is as follows, a few simple steps Http://wiki.debian.org/wl After the NIC is driven, install management tools Http://wiki.debian.org/WiFi/HowToUse Discovery cannot connect to wireless network so Http://wiki.debian.org/NetworkManager#doc Set managed=true in/etc/networkmanager/networkmanager.conf /etc/ini

Http://archive.cnblogs.com/a/2209414/fedora System Using Broadcom bcm4312 wireless network adapter After the fedora system is installed (, 15), The Broadcom bcm4312 wireless Nic cannot be used. You can enable the wireless Nic using the following methods! I use the first one ~1. Use the kernel module b43 + firmware to drive the bcm4312 wireless Nic After the fedora system is installed, there are b43 modules,

[Root @ localhost ~] # Rpmbuild-bb tg3.spec[Root @ localhost ~] # Cd/usr/src/redhat/RPMS/x86_64[Root @ localhost ~] # Rpm-ivh tg3-3.133d-1.x86_64.rpm 3. Load modules[Root @ localhost ~] # Modprobe tg3[Root @ localhost ~] # Vim/etc/modprobe. confAlias eth0 tg3Alias eth1 tg3Alias eth2 tg3Alias eth3 tg3 4. Restart the server and the NIC will be displayed. RHEL6.4 install the Broadcom BCM4313 wireless NIC Driver The B