Alibabacloud.com offers a wide variety of articles about cisco 2948g configuration guide, easily find your cisco 2948g configuration guide information here online.
(config ) #router NBSP;RIPNBSP;NBSP;NBSP;NBSP;NBSP;NBSP;NBsp;//Entering routing configuration mode - Enable RIP protocol router (config-router) #version 2 //using version 2, RIPV2 protocol router (config-router) #network 192.168.1.0 NBSP;//Specifies the network that needs to be advertised (located in the routing interface) Router (config-router) #network 222.200.105.0router (config-router) #exit/*=part3 static NAT
is of type Rstpswitch (config) #endSwitch #showspanning-tree nbsp//determine root switch, port role, port status, etc. # Link Test PC0 (Command prompt cmd) ping 192.168.1.4//link switch0switch>enswitch#conf tswitch (config) #inter f0/23 Turn off Port switch (config-if) #shutdownPC0 (Command prompt cmd) on the main link ping 192.168.1.4//link//Backup link flag changed from yellow to green, indicating backup link is enabled Lab Environment: Windows 7, C
[CISCO] NAT configuration full guide vronat NAT Function configuration introduction with the rapid development of the internet, the shortage of IP addresses has become a very prominent problem. A variety of solutions have emerged to solve this problem. The following describes an effective method in the current network
(VLAN) #exitSwitch #showvtp status//viewing VTP configuration information switch#show vlanbrief// Display VLAN configuration information switch#conftswitch (config) #inter f0/1switch (config-if) #switchport accessvlan The 2//divides the port into Vlan2switch (config-if) #exitSwitch (config ) #inter f0/2switch (config-if) #switchport NBSP;ACCessvlan3//divide the port into Vlan3switch (config-if) # Exitswitc
: On the emulator, you cannot use the show port-security command on a layer 3 switchPC Settings 192.168.1.2//pc0192.168.1.3//pc1192.168.1.4//pc2192.168.1.5//pc3//Subnet mask and gateway 255.255.255.0 192.168.1.1PC (Command prompt cmd) ipconfig//view MAC address of 4 PCs separatelySwitch0 configuration switch>enswitch#conf tswitch (config) #inter rang f0/1-22switch (config-if-range) #switchport mode access/ /config
//Set the host name s2960s2960 (config) #interface fastethernet0/ 1//Enter configuration mode S2960 (config-if) #exit //return to previous level mode S2960 (config) #ip address192.168.1.1255.255.255.0 //Set Switch IPS2960 (config) #ip default-gateway192.168.1.254//Set the default gateway S2960 ( Config) #ip domain-namecisco.com //Set the domain name S2960 (config) #ip name-server200.0.0.1 //Setting the domain name server S2960 (config) #no ip domai
Vlan2switch (Config-vlan) #vlan 3 //creating Vlan3switch (Config-vlan) # Exitswitch (config) #inter f0/2switch (config-if) #switchport accessvlan2 //set the port mode to Accessswitch (config-if) #exitSwitch (config) #inter f0/3switch ( CONFIG-IF) #sw acvlan3 //set the port mode to Accessswitch (config-if) #exitSwitch (config) #inter f0/1switch (config-if) #sw modetrunk// Set the port mode to Trunkswitch (config-if) #endSwitch #showvlan //View VLAN configur
) #port-channelload-balancedst-ip//to achieve load balancing by Destination IP address switch ( Config) #exSwitch #showetherchannelsummary NBSP;NBSP;NBSP;NBSP;//Display Ethernet Channel Information Switch#conftswitch (config) #interface port-channel1 //port configuration mode switch (config) into the aggregation port #exSwitch #showinterfacesetherchannel //displaying aggregation port information PC0 (Command prompt cmd) ping 192.168.1.3//link ping 19
Cisco AnyConnect, under Ubuntu configuration Windows/mac/android/ios can be downloaded to the Cisco website AnyConnect software, all have visual software can be used.Linux can be connected to a Cisco VPN with VPNC. sudo apt-cache search VPNC You can see that a number of related packages have been returned. One of the
3.12 layer-3 Switching Purpose: 1. master the basic configurations of layer-3 switching for inter-VLAN communication. 2. Understand the implementation principle of layer-3 switching. Tutorial topology: 650) this. width = 650; "src =" http://www.bkjia.com/uploads/allimg/131227/062203O08-0.png "title =" 3.12.png "/> Tutorial steps: 1. Deploy the Trunk link between SW1 and SW2 Based on the topology shown in the figure. The configuration is as follows:
refresh the cache to find650) this.width=650; "Style=" background-image:none;padding-left:0px;padding-right:0px;border-top-width:0px; border-bottom-width:0px;border-left-width:0px;padding-top:0px; "title=" lip_image029_thumb3 "border=" 0 "alt=" lip_ Image029_thumb3 "src=" Http://s3.51cto.com/wyfs02/M00/7D/C2/wKioL1bvmTWgM9FxAAHXmre7Xd0988.gif "width=" 579 "Height = "260"/>Limited number of words, follow-up information please see the next articleWindows.server.2008.r2.active.directory.
Start building with 50+ products and up to 12 months usage for Elastic Compute Service
1 on 1 presale consultation
24/7 Technical Support 6 Free Tickets per Quarter Faster Response
Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.
A comprehensive suite of global cloud computing services to power your business
Payment Methods We Support
