cisco 2960 configuration

Cisco 2960 Switch Configuration1. Cisco Working mode classification and function#用户模式仅答应基本的监测命令, the configuration of the router cannot be changed in this mode.Switch> #用户模式#允许用户执行所有的测试, view, save and other commands, this mode can not be modified router configuration, gener

1. Experimental topology650) this.width=650; "Src=" https://s4.51cto.com/wyfs02/M00/97/B2/wKiom1kxPDizomXqAABw1vEUgaA990.jpg-wh_500x0-wm_ 3-wmp_4-s_3605733301.jpg "title=" rspan.jpg "alt=" Wkiom1kxpdizomxqaabw1veugaa990.jpg-wh_50 "/>2. Switch configuration4F-IDC-01 ConfigurationVLAN 100Remote-spanMonitor session 1 Source VLAN 13Monitor session 1 destination Remote VLAN 1004F-IDC-04 ConfigurationVLAN 100Remote-spanMonitor session 2 Destination interface GI0/7 ingress untagged VLAN 13Monitor sessi

Microsoft's Windows Server 2012 has been able to support LACP link aggregation, due to the use of link aggregation can achieve line redundancy and bandwidth increase, here I used a Cisco 2960 to do a test for interested friends reference.Experiment Preparation:Cisco switch 29,601, install server 2012 servers, there are two Gigabit network card, network cable two root.Steps:1.

renaming its configuration file.6. After the switch restartsReboot the switch into the mode switch> switch>enEnter en into privileged mode and change the previously renamed configuration file back to switch#rename flash:oldconfig.text flash:config.textTo copy a configuration file to a running file switch#copy flash:config.text system:running-configThen go to

(config-if) #service-policy input down---> Restricted download2, limit the user's upload 5m(1), for IP address speed limitSwitch (config) #access-list 101 Permit IP host 10.10.10.100 anySwitch (config) #class-map match-all Output-classSwitch (CONFIG-CMAP) #match Access-group 101Switch (config) #policy-map 5mSwitch (config-pmap) #class Output-classSwitch (config-pmap-c) #police 5000000 1000000 exceed-action DropSwitch (config) #int f0/1---> Xia lian portSwitch (config-if) #service-policy input 5

Command for basic configuration of Cisco2950 vswitch 1. Configure the IP address To be able to be managed by a network management switch, a management IP address must be assigned to it. By default, VLAN 1 of a CISCO switch is managed. VLAN, Which is configured with an IP address for the VLAN, and the switch can be managed by the network. The command is as follows: A. Go to global mode: Switch # configur

4.2 related configuration of access switches# # In this example, we are connecting to an access switch where the GI0/1 port is allied to the core switch. It also means that we need to configure GI0/1 as trunk port. The specific configuration is as follows:D-2960-3 (config) #int GI0/1D-2960-3 (config-if) #swD-

LAN is not changed, and the configuration and access control list of the external network Port WAN needs to be changed .Increase the configuration of the VPDN. Assuming the username is admin, password 123456, the configuration process is as follows:This case is XX Telecom ADSL PPPoE access, need to use a common ADSL modem and a

Cisco configuration instance _ Cisco dual-Egress NAT configuration objective: to simulate the routing function based on the original address policy when a dual-Egress link is available, and access to the external network from different original addresses is realized, in most cases, the vro uses NAT to translate the Int

How to back up configuration files for Cisco, ruijie, And Juniper Devices For a company of a certain scale, network device configuration file backup is also a task that cannot be ignored, to prevent one day after your network device fails, you can recover in the shortest time, reduces losses for the company. The following describes the backup operations for sever

Previous page Everyone talked about Cisco Basic Operation command switch, while dragon boat holiday, the Cisco simple switch configuration, and hope you share "Happy Dragon Boat Festival"! Ok, configure the switch, first, you must enter the global configuration mode switch, successfully connect the switch and landing s

For Cisco Network Assistant (CNA), it is estimated that Cisco has launched a free tool that can be used to configure Cisco devices such as Catalyst switches, PIX firewalls, IP phones, and wireless access points, CNA support, As long as it is facing small and medium enterprises. CNA provides a number of features and wizards. The following figure: CNA provides

Configuration example of cisco router and layer-3 Switch environment, cisco layer-3 SwitchSimple environment configuration instance for cisco router layer-3 Switch I. network topology: Ii. configuration command: 1. vro

Basic configurations of Cisco routers and Cisco router configuration commands En -- enter the privileged mode config t -- enter the global configuration mode wr (OR) -- save the configuration (otherwise, the configuration fails be

(Config-router) #exitIf this is all configured, then use the ping command to test it!Here is a start-up-configuring HSRP Hot Spares:Configure on the active three-layer switch:Switch (config) #interface vlan 1Switch (config-if) #standby 1 IP 192.168.1.254Switch (config-if) #standby 1 priority 200Switch (config-if) #standby 1 track fastethernet 0/2Switch (config-if) #standby 1 preemptConfigure on the backup layer three switch:Switch (config) #interface vlan 1Switch (config-if) #standby 1 IP 192.1

Lab Environment:Routers make Tp-link set up NAT forwarding, Tp-link router gateway is set to 192.168.30.254 ( core layer) Cisco 35,503 layer switch (model C3550-I5Q3L2-M) configuration three Vlan,vlan 10, VLAN 20, and VLAN 30IP address for VLAN 10:192.168.10.1/24IP address for VLAN 20:192.168.20.1/24FA0/24 ports are configured as trunk port-level converged layer Cisco