interconnected with layer-3 switches. When using a router to connect to a vrovlan, you generally need to set sub-interfaces corresponding to each VLAN on the LAN Interface, while a layer-3 Switch generates a "VLAN Interface" internally )". A VLAN interface is an interface u
How to select a layer-3 SwitchAt present, layer-3 switches are showing a strong growth trend and are replacing routers in Lan. Their huge market potential is attracting a large number of domestic and foreign manufacturers to join the competition. Fortunately, Chinese manufacturers have developed their own ASIC chips an
exchange chip that can generate Gigabit and MB ports; one is a CrossBar chip that only outputs Internal High-Speed interfaces (usually at a rate of over 10 Gbit/s) for interconnection between modules.
Currently, Cisco, Extreme,, gangwan, and other vendors have launched CrossBar-based core switch products. However, many products on the market still use gigabit port
support direct access to G.703ITU's standard on physical and electrical characteristics of various digital interfaces, including 64kbps and 2.048Mbps interfaces, the G/V converter must be used. In branch nodes, high-end routers are generally not configured, and even low-end routers are several times more expensive than switches. Therefore, the layer-3 Switch Tec
Internal High-Speed interfaces (usually at a rate of over 10 Gbit/s) for interconnection between modules.
Currently, Cisco, Extreme,, gangwan, and other vendors have launched CrossBar-based core switch products. However, many products on the market still use gigabit port interconnection, it is mainly intended for users with high performance requirements and high
to the native understanding, when a non-TAG port receives a data frame and contains a vlan id, make a judgment, if the vlan id is the PVID of the port, it can be received; otherwise, it is discarded.
If the port that receives the data frame is a TAG port and the data frame is a common data frame, the default vlan id o
CrossBar technology, two types of layer-3 switching chips are generally used: one is an exchange chip that can generate Gigabit and MB ports; one is a CrossBar chip that only outputs Internal High-Speed interfaces (usually at a rate of over 10 Gbit/s) for interconnection between modules.
Currently, Cisco, Extreme,, gangwan, and other vendors have launched CrossB
Gbit/s) for interconnection between modules.
Currently, Cisco, Extreme,, gangwan, and other vendors have launched CrossBar-based core switch products. However, many products on the market still use gigabit port interconnection, it is mainly intended for users with high performance requirements and high price sensitivity.
2. Access Control Based on hardware line
ICMP Echos to 192.168.20.1, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 24/48/84 MS
From the above, we can see that through the deployment of layer-3 switching technology, the host between VLANs can communicate with each other. This experiment is complete.
[PL1]Disable layer
switching chips are generally used: one is an exchange chip that can generate Gigabit and MB ports; one is a CrossBar chip that only outputs Internal High-Speed interfaces (usually at a rate of over 10 Gbit/s) for interconnection between modules.
Currently, Cisco, Extreme,, gangwan, and other vendors have launched CrossBar-based core switch products. However, many products on the market still use gigabit
Layer-3 Switch SLB interface configuration layer-3 Switch configuration-configure a group of layer-2 ports www.2cto.com configure terminal to enter the configuration status nterface ran
There are many things worth learning about layer-3 switches. Here we mainly introduce the development status of the new technology in layer-3 switches. The physical connection from the line card to the switch structure in the shared switching architecture is simplified to a
China 3 layer Switch VLAN isolation192.168.1.0---------g1/0/1 S SW g1/0/2-------192.168.2.0192.168.3.0-----------------------|192.168.4.0-----------------------|Prohibition of 1.0, 3.0, 4.0 and 2.0 visits[H3c]acl Num 3000[H3c-acl-adv-3000]rule deny IP source 192.168.1.0 0.0.0.255 destination 192.168.2.0 0.0.0.255//Forbidden 1.0 Access 2.0[H3c-acl-adv-3000]rule de
data processing.
(1) Hardware-only layer-3 technology is relatively complex, costly, but fast, with good performance and strong load capabilities. The principle is to use an ASIC chip and hardware to search and refresh route tables. When the data is received by the port interface chip, first find the target MAC address in the
Layer-3 Switch Equipment is still quite common, So I studied how to identify the performance of layer-3 Switch Equipment. Here I will share with you, I hope it will be useful to you. With the gradual development of network applica
Layer-3 Switch configuration-configure a group of layer-2 ports
Configure terminal enters configuration status
Nterface range {port-range} enters the group configuration status
Layer-
Switch module broadcasts an ARP request to Site B based on the route information. Site B receives the ARP request and then replies to the layer-3 Switch module with its MAC address, the layer-3 Switching Module saves the address
Currently, most layer-3 switch devices in the market support link aggregation and Spanning Tree Protocols, which can effectively improve the overall network performance and meet more user needs. With the gradual development of network applications, telecom-grade switches, especially layer-
Experiment on single-arm routing using a layer-3 Switch
In the real environment, sometimes the gateway is not necessarily enabled on the router, sometimes the single-arm routing function is not necessarily connected to the interface on the router, you can use a layer-3
With the distributed pipeline, multiple distributed forwarding engines can quickly send data packets independently. In a single pipeline, multiple ASIC chips simultaneously process multiple frames. This concurrency and pipeline improves the forwarding performance to a new level: On-Demand Unicast, Broadcast, and Multicast on all ports.
3. dynamically Scalable Memory
For advanced LAN switching products, the real performance is built on an intelligent
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.