cisco cluster command switch

interface is working in chaotic mode, read all the data frames in the network. This pattern is typically used to test data flowing through the network.If the interface works in non-chaotic mode, only the data that is broadcast and posted directly to this interface is read.18. Input packets and bytes3109298 packets Input, 186557880 bytes, 0 no bufferThe first represents the total number of error-free packets received by the router. Second, it also represents the total number of bytes received by

Q: Are there any simple tools and methods? Do a script, automatically execute on a script in N-around Cisco switches, and then return the results? Method One, the switch configuration file download, modified and uploaded to the n-switch. Then restart or copy start run. Method Two, under Windows to build a bat file, the contents and you telnet to the

"Copyright notice: Original translation articles, translation level is limited, errors are unavoidable,The Translator is not responsible for the consequences of errors or omissions in the article, please be careful to reprint them. Reproduced please retain this statement and source: blog.csdn.net/shallnet, download the English version of the book "The most important commands on the Catalyst platform switch for STP areShow Spantree。 Although this

"1" resolves the cisco switch password forgetting reset method:1, power off + the front panel hold down the mode key, and then re-power, always press the switch front panel port 1 indicates from green to off does not light off, automatically into the switch mode;2, input? See what configuration commands are (optional),

The cisco 2621 router networking configuration command uses the cisco2621 router to form a small LAN, note: Configure command 1, configure the access password conf tenable secret flw521521line vty 0 4 password Authentication service password-encryption limit 2, configure interface IP enableconf tinter fa0/0ip address 192.168.2.2 255.255.255.0no shutdown inter fa0

-interface IP address.CliSwitchSwitch (config) #vlan 2Switch (Config-vlan) #exitSwitch (config) #vlan 3Switch (Config-vlan) #exitSwitch (config) #int F0/2Switch (config-if) #switchport Access VLAN 2Switch (config-if) #int F0/3Switch (config-if) #switchport Access VLAN 3Switch (config-if) #switchport mode trunkRouter:Router (config) #int f0/0Router (config-if) #no shRouter (config-if) #int f0/0.1Router (config-subif) #encapsulation dot1q 2Router (config-subif) #ip add 192.168.1.1 255.255.255.0Rou

Command for basic configuration of Cisco2950 vswitch 1. Configure the IP address To be able to be managed by a network management switch, a management IP address must be assigned to it. By default, VLAN 1 of a CISCO switch is managed. VLAN, Which is configured with an IP address for the VLAN, and the

Switch command-Huawei1. Set the host name/system name on the IOS-based switch:Switch (config) # hostnameSet the host name/system name on the CLI-based switch:Switch (enable) set system name-string2. Set the logon password on the IOS-based switch:Switch (config) # enable password level 1 passwordSet the logon password on the CLI-based switch:Switch (enable) set passwordSwitch (enable) set enalbepass3. Set re

interface rate: Speed "10|100|100"Never timeout:Line con 0Exec-timeout 0 0Information synchronization:Line con 0Logging Synchronous (Logg SYN)Disabled DNS Query:no IP domain-lookupSwitch:View Mac Address table:show mac-address-tableView F0/1 information (including duplex mode and rate):Show int F0/1Enable routing on layer three switches:IP RoutingView interface mode status: show interface Interface-id switchportTo create a VLAN:1.vlan DatabaseVLAN vlan-id [name vlan-name]Exit2.conf TVLAN Vlan-

Switch command 2-Huawei20. to configure a switch as a command switch of a cluster, you must first assign an IP address to the management interface and then use the following command:Switch (config) #