cisco ip sla configuration guide

The IP SLA is an abbreviation for the Internet Protocol Service-level Agreement, which means the Internet Protocol Service level agreement. IP SLAs are mainly used in the following situations:1. Static route Next-hop detection.2.HSRP out interface detection.The 3.PBR policy routes the next hop detection.650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/5

{PRIMARY:NODE0} [Edit Services][Email protected]# ShowRPM {Probe Probe-2nd-line {Test 2nd-isp {Target address 11.22.33.44; //Probe target address, probe type default is Icmp-pingProbe-count 6; How many times, 6 times?Probe-interval 10; The detection interval is 10 seconds each time.Test-interval 15; 6 times a cycle, how many seconds each cycle interval, 15 seconds. It means that there is No 10 seconds to send a ping, 6 times, 6 times, and so on for 15 seconds in a new round of detection.History

{PRIMARY:NODE0} [Edit Services][Email protected]# ShowRPM {Probe Probe-2nd-line {Test 2nd-isp {Target address 11.22.33.44; //Probe target address, probe type default is Icmp-pingProbe-count 6; How many times, 6 times?Probe-interval 10; The detection interval is 10 seconds each time.Test-interval 15; 6 times a cycle, how many seconds each cycle interval, 15 seconds. It means that there is No 10 seconds to send a ping, 6 times, 6 times, and so on for 15 seconds in a new round of detection.History

LAN is not changed, and the configuration and access control list of the external network Port WAN needs to be changed .Increase the configuration of the VPDN. Assuming the username is admin, password 123456, the configuration process is as follows:This case is XX Telecom ADSL PPPoE access, need to use a common ADSL modem and a

----------- --------------------------------------------------------GI1/0/1 Ip-mac INACTIVE-NO-SNOOPING-VLANGI1/0/2 Ip-mac Active Deny-all deny-all 24GI1/0/3 Ip-mac INACTIVE-NO-SNOOPING-VLANGI1/0/4 Ip-mac Active Deny-all deny-all 24GI1/0/5 Ip-mac Active Deny-a

Cisco routers use many methods in configuration. Using SSH instead of Telnet cisco makes it easier for us to understand the configuration of cisco routers and other knowledge points. Replacing Telnet with cisco router

Cisco Wireless AP Configuration Guide requirements in complex enterprise environments Overview: using Cisco AP to build an enterprise wireless LAN, users' laptops do not need to be added to the AD domain,You can log on to the wireless network. the user name and password of the domain are used for Logon. SSIDS hides the

Https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/7-x/security/configuration/guide/b_ Cisco_nexus_9000_series_nx-os_security_configuration_guide_7x/b_cisco_nexus_9000_series_nx-os_security_ Configuration_guide_7x_chapter_01.html Feature Description Changed in Release Where documented IP ACLs Added

configuration is as follows:Pix515e (config) # global (outside) 1 222.20.16.100-222.20.16.200 netmask 255.255.255.0Pix515e (config) # global (outside) 1 222.20.16.201 netmask 255.255.255.0Pix515e (config) # nat (outside) 1 0.0.0.0 0.0.0.08. dhcp serverIn the internal network, Dynamic Host allocation IP address server (dhcp server) is enabled for centralized management of maintenance and full use of limited

to say, after you set the password for level 1, you will be asked to enter the password next time you connect to the switch and enter K, this password is the password set for level 1. Level 15 is the privileged mode password that you enter after you enter the enable command. Step 2: Set the VLAN name. Because the four VLANs belong to different switches, the command for VLAN naming is VLAN 'vlan No. 'name' vlan name ', the following code configures VLAN 2, VLAN 3, VLAN 4, and VLAN 5 on the Switc

the ports of the corresponding vswitch as required in table 1. To verify our configuration, you can use the show vlan command in privileged mode to display the configuration you just made and check whether it is correct. The above describes the VLAN configuration of the Cisco Catalyst 1900 switch. The VLAN

Recently, a number of Cisco ucs c Series servers have been added. After two weeks of deployment and installation, the server can finally be tested. This document briefly introduces the network configuration of the Operating System (centos 6) in the Cisco UCS server. It can be simply considered that this article describes the network

, with the same level of security services being provided, the PIX configuration is much simpler than setting up a proxy server. In theory, all you need to do is specify an IP address and an address library for external access, an IP address and network mask for internal connections, RIP, timeouts, and other collateral security information. Here is a PIX firewall

Cisco switch VLAN interface IP Address Configuration 1. vswitch VLAN Interface static IP Address Configuration switch VLAN Interface static IP Address Configuration function requirement

The Cisco router market is very good. Many people may not understand how the Cisco router solves the router IP configuration parameters. It does not matter. After reading this article, you will certainly have a lot of GAINS, I hope this article will teach you more things. For Cisco