Discover cisco load balancing router, include the articles, news, trends, analysis and practical advice about cisco load balancing router on alibabacloud.com
minutes
System returned to ROM by reload
System image file is "flash: c2600-i-mz.121-14.bin"
Procedure for upgrading a Cisco 3600 series router with a PCMCIA card
Create a console session to the vro
Check the remaining space of the flash card (PCMCIA slot)
Check whether the TFTP server has an IP connection to the vro.
Copy new image to flash memory via TFTP Server
Set the boot instruction to
12000 the Cisco router series is very suitable for small and medium-sized enterprises. Here we mainly analyze the performance characteristics of the Cisco router series. In today's information age, enterprise mail has become an essential tool for business communication and communication. With the new routing technology
, it does not affect the delivery of the service, resulting in high availability.Different implementation methods of load balancing4.1 Load balancing with dynamic network address translation (NAT) capabilities for network devicesRequirements for load Balancing:A router with
Software load Balancing is generally implemented in two ways: the implementation of soft load based on operating system and the implementation of soft load based on third party application. LVS is a kind of soft load based on Linux operating system, Haproxy is an open source
address translation is not enabled. Command mode: global configuration mode. Note: the destination address translation in NAT can be used to achieve TCP load balancing. You can use a virtual host to receive users' TCP requests instead of multiple actual hosts, NAT maps these requests to each actual host in turn to achieve load
four-layer load balancing , that is, mainly through the message of the destination address and port, coupled with the load Balancer device settings of the server selection method, determine the final choice of internal server.In the case of common TCP, the load balancer device, when it receives the first SYN request f
It is very important to know some knowledge about backing up the cisco router configuration file to make our vro more secure. Here we will give you a detailed introduction to this issue in several steps. The COPY command is often used during vro configuration. Next we will introduce how to use the COPY command to back up the configuration file, and how to COPY and back up the
types of load balancing implementations are:
Software-based load balancing. Software-based load Balancing includes special software that is installed on the server in a load-b
One, the internal components of the Cisco routerIn order to configure, Cisco Internetwork and troubleshoot, we must first understand the major components of the Cisco routers and understand these componentsThe respective function.Table 7-1 gives a description of the major components of the Cisco
the environment.
4. E-commerce Web site High-performance, highly available solutions, LVS load balancing (front-end four-tier load balancer).
5. The key point explanation of the construction process, the key step explanation.
6. This program has been used in practical production applications for many times, and can be flexibly applied.
Second, the software
Dynamic and robust routing is extremely important for Internet networks. Therefore, any network engineer who is first involved in this field must not only understand the concept of routing, but also be able to control it in a real environment. However, the products provided by high-end network equipment suppliers such as Cisco in the routing field are all over the world. This means that most people can only learn routes in school or laboratory environ
HSRPcisco and VRRP are the most common gateway redundancy technologies. Similar to VRRP, HSRP is composed of multiple routers.
A vro is a virtual gateway, and a vro is active.
It is replaced by a device to implement transparent switching to users. However, we hope to achieve redundancy at the same time.
Load Balancing to make full use of the capabilities of the device, GLBP (
into global IP addresses on the NAT router when communicating with the outside world.
Additional Benefits of Load balancing
High scalability
High concurrent requests can be better addressed by adding or reducing the number of servers.
(server) Health Check
The load balancer can improve reliability by checking the heal
data packet processing speed of the router depends largely on the type and performance of the CPU. The memory router uses the following memory types, each of which assists the router in different ways. 1. read-only memory (ROM) Read-only memory (ROM, Read. ly Memory) features in Cisco routers are similar to ROM in com
, enable NLB on the appropriate adapter, and then configure the cluster's IP address.
cause : You have added the IP address of the cluster to the network adapter that is not already enabled for NLB.
Solution : Remove the IP address of the cluster from the TCP/IP properties of the incorrect adapter, enable NLB on the appropriate adapter, and then configure the cluster's IP address.
For more information about enabling NLB, see Installing Network
Cisco access routers are combined with the media encryption features on Cisco IP phones and Cisco CallManager to provide a secure environment for IP communication across the WAN or LAN. As shown in, SRTP is used to encrypt voice calls from the voice network module in branch. This provides secure calls between analog phones or fax machines in the office. Likewise
prompts whether the SETUP mode is enabled. 2. The following table describes the specific meaning of each register during the custom router startup process. It is in hexadecimal notation and 0X cannot be omitted. BitHex meaning 0-30x0000-0x000f start zone 60x0040 ignore content in NVRAM 70x0080OEM position 80x0100 do not allow break Key interrupt start 11-120x0800-0x1800 console line rate (CISCO and Huawei
Recently participated in A10 load balancing equipment training and wrote basic configuration notes based on personal understanding. Cisco ACE modules have been used before, and the fundamentals are consistent.
Note: If there is an understanding error please give the point, thank you.
The notes are as follows:
A10 Load
used as MySQL, mail or other non-web load balancing, we often use it as a MySQL (read) load balancing;Four, with a strong monitoring server status of the page, the actual environment we combine Nagios Mail or SMS alarm, this is also I like it one of the reasons;Five, Haproxy support virtual host.
When doing a
. However, it should be pointed out that IGMP supports multicast only when NLB is configured.(Multicast) mode.
When you select multicast mode, there is a repeat option "IGMPMulticast (IGMP Multicast) ". If this option is selected, NLB retains the original MAC address, but addsIGMP multicast address. In addition, the NLB host sends an IGMP message for this group. If the switch detects these messages, it can use the desired multicast address to fill in its ownIn this way, the inbound traffic will
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.