Preparation: A PC with a TFTP server, a router with iOS, and a cable connectionSet the router interface and the IP address of the computer card on the same network segment, and can ping each other.1 , install Cisco TFTP Server2 , set the TFTP log path and file storage pathNote: During the entire download process, TFTP server cannot shut down3 , Configure the IP o
Tags: Cisco router forgot enable passwordSteps:1. Restart the router that appears on the router ROM Monitor mode, press "Ctrl+breack" Key to enter ROM mode, such as:650) this.width=650; "title=" capture. PNG "style=" float:left; "alt=" Wkiol1nkiftr_sdkaaa1fp9kntk338.png-wh_50 "src=" https://s4.51cto.com/wyfs02/M00/A7
There is a bit of crooked nuts on the forum sigh "Cisco router QoS project monitoring is always painful", admittedly, the general router traffic monitoring, using cacti to do, and due to the different upgrade version number, and the router iOS version is different, and very difficult, Some programs even need to TFTP do
Implementation of VPN on a Cisco router: 1. software requirements: IOS with performaniseplusistmc56 is required. Currently, stable versions are 12.07T2. Hardware requirements: 8 mbflashand40mbram in DownloadIOS, the software and hardware requirements of the downloaded IOS version are prompted. 3. IPSec manual method considerations
Implementation of VPN on a Cisco
China Mobile's GPRS network uses the APN method to connect to the GPRS device terminal and communicate with the server through the APN. The customer purchased the Cisco 2811 router, and the mobile company needed to pull the optical fiber through the E1 port, I spent more than 1000 RMB with an E1 module. mobile companies are doing very poorly, and optical fiber connectors are not provided at all. I also boug
For Cisco router authentication, when performing the cisco Route Selection protocol (r12002; VPN) authentication, the key is irrelevant to the key ID when using plain text (General authentication, during MD5 authentication, the key and key ID are related, that is, the key IDs and keys at both ends must be the same, for example, R1 (config) # key chain key1 R1 (co
I. Overview:
Cisco 15.2 iOS support IKEV2 IPSec VPN, security is more IKEV1, the first phase of authentication methods also have a variety of ways to support the local and remote use of different authentication methods, this test for both sides both local and remote use of preshared key method.
Two. Basic ideas:
The A.VPN peer is configured with a static VTI mode while the dynamic VTI mode is used.
B. The actual test found that the VTi interface c
Tags: erase cmd terminal copy Cisco forgot password direct out settingLab tasks:1. Configure the password in Cisco mode routing2. How to reset the password after forgetting the passwordExperimental steps:1. Give Router a password:Router >enable#config TRouter (config) #line vty 0 4//Incoming Remote management interface#password//123 Configure password 123Exit
router. PDLM is written by the Packet Description Language Module, which means the data Packet Description Language Module. It is a description of the protocol layer of high-level network applications, such as the protocol type and service port number. Its advantage is to adapt NBAR to many existing network applications, such as http url, DNS, FTP, and VoIP. At the same time, it can also be defined, to enable NBAR to support many emerging network app
Configure the PPPoE configuration for connecting a CISCO router to an ADSLmodem through the PPPoE configuration: hostnamebjsite! Ipsubnet-zeronoipdomain-lookup! Vpdnenablenovpdnlogging! Vpdn-group1request-dialinprotocolpppoe! Interfaceethernet00ipaddh
Configure PPPoE for connecting a CISCO router to an ADSL modem using
Dhcp configuration commands for Cisco router R1 (server) -------------------- R2 (client) www.2cto.com dhcp configuration of Cisco router and their explanations are as follows: r1dhcp service configuration dhcp # configure terminal // enter global mode dhcp (config) # service dhcp // enable dhcp (config) # no ip dhcp c
On CISCO routers, there are ROM, NVRAM, RAM, and Flash. the four storage media have different functions. IOS is loaded in FLASH. RAM stores the current running configuration file (running-config) of the router, and the current startup configuration file (startup-config) of the router) it is stored in NVRAM, And the mini iOS, BootStrap, and RomMonitor running mode
; Note that the enable password and vty password can only be connected by the pc telnet we use PC to telnet router and of course we're still using putty. on one router. telnet 650) this.width=650; "style=" Float:none; "title=" 3.JPG "src=" http://s2.51cto.com/wyfs02/M02/7D/2E/ Wkiom1bhajdaou-vaadbdumazkq095.jpg "alt=" wkiom1bhajdaou-vaadbdumazkq095.jpg "/> After landing the
How to Set Up r12002 routing protocol for Cisco router 3620 to demonstrate how to set up r12002 routing protocol for Cisco router 3620 this time, we need to build a complex network experimental environment, this environment is also the experimental environment used later to learn about other
When a Cisco router forgets or loses the enable password, there are two ways to recover, depending on which series of routers you are using.
The first of these methods
This approach restores the following routers: Cisco 2000 series, 2500 series, 3000 series, Cisco 4000 series using the 680x0 Motorola CPU, and 10.0 se
The Cisco router sets IOS to upgrade each other. My company's network department has a Cisco router 2501, but IOS is bad. Here I call it cisocB, and another 2501 router IOS is good, we prefer ciscoA. Good IOS is no longer available on my PC, but it is transferred to the PC t
encapsulation method used by the serial port or ISDN InterfaceEncapsulation sap specifies that the Ethernet 802.2 format Cisco password used on the network segment is SAPEnd exit Configuration ModeErase deletes flash memory or configures CacheErase startup-config Delete content in NVRAMExec-Timeout: specifies the time that the exec command interpreter has waited before user input.Exit to exit all configuration modes or to close an active Terminal ses
Assume that two Cisco routers and R1 (server) connect to R2 (client) to form a simple chained lan. DHCP is implemented below. The configuration commands and explanations are as follows:
1. Configure the R1 dhcp Service
Dhcp # configure terminal
// Enter global Mode
Dhcp (config) # service dhcp
// Enable the dhcp Function
Dhcp (config) # no ip dhcp conflictlogging
// Disable dhcp logging
Dhcp (config) # ip dhcp pool
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.