of the exec.py machine will be configured to 1.1.1.8/10 the problem is, if I buy 10 boxes, how do I tell which box the data I send will arrive? At this time, think of the CDP, the box first put its own information, including the identification serial number, including the MAC address group broadcast, and then similar to the Winbox program to receive multicast messages, users follow this type of information to configure the specific box!This completes the automatic configuration of all: 0. Conne
setting the routing entry on the YONG3 on the 192.168.1.0 network segment, ping192.168.2.2 on the Yong1 to ping theYong3 (config) #ip Route 192.168.1.0 255.255.255.0 s/0/3/0Yong3 (config) #endYong3#sh IP routeGateway of last resort are not setS 192.168.1.0/24 is directly connected, Serial 0/3/0it has an administrative distance value of 0C 192.168.23.0/24 is directly connected, Serial 0/3/0Yong3#ping 192.168.1.1Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 192.168.1.1,timeout
Cisco800Series routers Cisco 800Series routers are customized for small offices and remote workers.Cisco IOSSoftware to provide enhanced network security and reliability. It is suitable20Small Offices of usersISDN,IDSLOr serial connection up512 Kbps) Connect each userInternetOr enterprise LAN. BenefitsCisco 800Customers of series
Summary of typical configurations of Cisco routers (2) how to use the Control Access Rate of a Cisco router to limit the traffic Rate of ICMP packets: www.2cto.com interface xy rate-limit output access-group 2020 3000000 512000 786000 conform-action transmit exceed-action drop access-list 2020 permit icmp any echo-reply refer to IOS Essential Features for more in
Some Suggestions on preventing distributed denial of service (DDoS) attacks on Cisco Routers
1. Use the ip verfy unicast reverse-path network interface commandThis function checks each packet passing through the router. In the CEF (Cisco Express Forwarding) Table of the router, the router discards the packet if it does not have a route from the source IP address
This article describes in detail how to configure Cisco routers in terms of global debugging, interface debugging, and Protocol debugging. I believe this article will help you.
Global debugging
When configuring a Cisco router, the boundaries between global and interface commands are obvious. In this case, we use "Global" to identify commands that cannot be used f
The steps below describe how to recover a password on the Cisco 600 series of routers.
Step 1: Enter RMON mode.
To do this, follow the steps below:
Connect your PC to the console port of the router.Set your Terminal Access Program (such as HyperTerminal in Windows) to the following settings:Baud rate: 38400 bps recommended (standard 9600 bps possible)Data bits: 8Parity: NoneStop bits: 1Flow control: NonePow
dedicated for network management or an application that executes management functions on a network device. Currently, many software and hardware vendors provide network management systems that support SNMP protocols, such as Cisco's CiscoWorks network management software products.
The SNMP agent is a software module in the managed device. It is used to maintain the management information data of the managed device and reports the management data to an SNMP Management System as needed. The SNMP
Two-line access technology for Cisco Routers
In some cases, we need to implement dual-line access to ensure stable operation of the network and ensure reliable service quality. The following steps can be taken:
1. Configure the IP address of the Internet access interface, which is generally from China Telecom or China Netcom.
2. Configure the access control list
3. Configure the NAT address pool
4. Configur
Basic configurations of Cisco Routers
En -- enter the privileged mode config t -- enter the global configuration mode wr (OR) -- save the configuration (otherwise, the configuration fails before the power-off)
1. Set the password for entering the vro Console
In global configuration mode, enter line console 0 --- enter the '0' Interface password 123 -- set the password to 123login -- set the console inter
.jpg " title= "Picture 9.png" style= "Float:none;" alt= "wkiol1raq7obhv8maaa0glucock888.jpg"/> 650) this.width=650; "Src=" http://s3.51cto.com/wyfs02/M00/4D/D0/wKioL1RaQ7TRpoYjAAAz23ZrzoI052.jpg " title= "Picture 10.png" style= "Float:none;" alt= "wkiol1raq7trpoyjaaaz23zrzoi052.jpg"/>5. Configure the Access control List on the R2 and use the f1/0 interface in the R2 to enter the direction650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/4D/D0/wKioL1RaSGyTYKPIAABPcoS7W1U149.jpg "style=
10 permit any! The router is prohibited from receiving and updating the route information of the 192.168.1.0 network.Router (Config) # router ospf 100Router (Config-router) # distribute-list 10 in! Disable router forwarding to spread route information of 192.168.1.0 NetworkRouter (Config) # router ospf 100Router (Config-router) # distribute-list 10 out6. We recommend that you enable the IP Unicast Reverse-Path Verification. It can check the accuracy of the source IP address and prevent certain
SYSTEM image according to the boot system command settings in the startup configuration, if this command is not set, the operating system image is loaded from the system image on a default network server.
When the 6th-bit value is 1, the configurations in NVRAM are ignored when the vro starts. For example:
0x0: the operating system image is not automatically loaded, but enters the ROM monitor mode and waits for the user to enter the command (for example, if the command fails in the pre
This article describes in detail how to classify Cisco routers. What are the features of each Cisco Storage? I believe this article is helpful to you.
Memory category:
1: RAM: Random Access to memory, equivalent to computer memory
2: ROM: read-only memory. Some microcodes used to start and maintain the router are resident in the ROM.
3: FLASH Memory, equivale
Router (config) # interface f0/0Router (config-if) # IP address 192.168.1.1 255.255.255.0Router (config-if) # no shutdownRouter (config-if) # exitRouter (config) #Router (config) #exitRouter #Router # Configure Terminal! Go to Global modeEnter configuration commands, one per line. End with cntl/z.Router (config) # enable password Cisco! Set Privileged PasswordsRouter # Write Memory! Save current configuration file to NvramRouter # Reload! Rebooting th
This site has previously shown us the method of segmenting a router into eight virtual routers using virtual Routing and forwarding (VRF, VM forwarding) through a scene example. I showed you how to configure VRF, and in this article we continue to use this scenario and, through IPSec configuration, replicate the exact topology and address to eight experimental environments. The entire environment can proceed smoothly, first requires the virtual route
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.