cisco2960

-02Motherboardserialnumber:FOC12022J7GPowersupplyserialnumber:AZS115017D4Modelrevisionnumber:D0Motherboardrevisionnumber:A0Modelnumber:WS-C2960-24TT-LSystemserialnumber:FOC1202W1WGTopAssemblyPartNumber:800-27221-03TopAssemblyRevisionNumber:B0VersionID:V03CLEICodeNumber:COM3L00BRBHardwareBoardRevisionNumber:0x01SwitchPortsModelSWVersionSWImage------------------------------------*126WS-C2960-24TT-L12.2(35)SE5C2960-LANBASE-MPressRETURNtogetstarted!Wouldyouliketoterminateautoinstall?[yes]:---SystemC

The first two days of the engine room a Cisco2960 of the port often down, at that time let the engine room restart switch also useless, later let change a mouth on the recovery, but over a period of time the port will be down, on-line check may be due to the port-security of the Cisco switch caused the port down, Later to the computer room connected to the switch to view the next, G17 Port display err-disabled, in order to confirm the reason is port-s

1. Configure the IP address to upload IOS and config.text filesSwitch#conf TSwitch (config) #int vlan 1Switch (config) #ip add 172.16.1.1 255.255.0.0Switch (config) #no shutSwitch (config) #endSwitch#ping 172.16.1.2// computer configured IP, to and

cisco:2960Switch (config) #line vty 0 4Switch (config) # password Ciscoswithc>enSwitch#inter VLAN 1Switch # IP address 10.88.103.84 255.255.255.0Switch (config) #IP default--gateway 10.88.103.1 (cross-network segment, without this, cross-network

In order to implement IP+MAC bindings on the two-layer switch Cisco 2960, you must use an Access-control-list-based approach.Pre-Implementation features: ip:168.31.6.199 and mac:001e.ec64.5a.83 bindingsStep One: Configure the Mac access control

Switches: Cisco2960, Cisco g3560xserver: 10.15.44.164 ac-*-2d-* -84-*pc:10.15.44.69Server 44.164→port 2-Cisco2960-port1→g3560x-port5Find this IP by IP address under the interface of that switchQuery the corresponding switch port via Mac, IP address1. Start running nbtstat–a IP query out MAC address650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M00/7C/ED/wKioL1bcv2eQDm6GAAAY8Id21zc609.png "title=" Qq

When clearing the Cisco2960 switch configuration file, flash is lost to erase due to misoperations. After reload, the system is dumpfounded. After you press enter, the switch without ios is displayed, and the prompt "switch:" is always displayed :"Www.2cto.com fortunately, I still have a switch of the same model here. My idea is to copy this binfile to the flash which cannot be started.Www.2cto.com First, export the binfile from a good switch (I use t

in3750 (config-if) # ip access-group outfilter out3750 (config-if) # exit3750 (config) # int vlan 103750 (config-if) # ip access-group 100 in3750 (config-if) # exit3750 (config) # int vlan 203750 (config-if) # ip access-group 101 in3750 (config-if) # exit3750 (config) # int vlan 303750 (config-if) # ip access-group 102 in3750 (config-if) # end2960Configuration:2960 # conf t2960 (config) # int f0/152960 (config-if) # switchport mode trunk2960 (config-if) # switchport trunk encapsulation dot1q296