Raspberry Pi When used alone, often need touch screen and soft keyboard for easy operation, micro-snow LCD display can better realize this function,Just as the lab buys a 3 b board and a 5inch monitor, it installs the official installation manual once.One: Material preparation
Raspberry
DIYA UAV Vision tracking system based on Raspberry Pi and PythonThe drone's image is stored and transmitted to the ground station in real time, which is almost standard. Suppose you want something advanced--to process the captured image directly on the drone and implement your own active control. In fact, visual tracking has been in some high-end consumer-class UAV has the application, just play out of the
Raspberry Pi on the Cloud (1): Environment preparationRaspberry Pi on the Cloud (2): Uploading sensor data to AWS IoT and leveraging Kibana for presentation1. Sensor installation and configuration 1.1 DHT22 installationThe DHT22 is a temperature and humidity sensor with 3 pins, the first pin on the left (#1) is the 3-5v power supply, the second pin (#2) is connec
software package is ready and can be released;
Iii. Cross-compiling source code
1. Environment
Ubuntu
2. Install Raspberry Pi cross compiling tool
Step1. download Raspberry Pi cross compiler tool https://github.com/raspberrypi/tools
Step 2: place the source code in a folder that users can share, such as/usr/tools.
Ste
:id 0bda:8178 Realtek Semiconductor Corp rtl8192cu 802.11n WLAN Adapter
You can see that the USB camera is Microdia Sonix USB 2.0 CameraThe driver of this device has been in the Linux-2.6, but Pidora is not supported by default, so you need to re-compile Linuxkernel, custom, support RTL8192CU and Sonix camera can be, and then made of RPM, Install via RPM:Click ( here) to collapse or open
RPM-UVH kernelxxxxxxxxx.rpm
Once installed, y
the component on the black drone frame.
If you want to connect the power supply parts to the power supply, pay attention to the following points. If you want to quickly connect the connector and power supply parts to the power supply, be careful about short circuits. You can remove the other end of the power supply module and then weld the battery and connector,
In this way, we can easily disconnect the drone battery and power supply components.
Finally, the battery and power supply components
Requirement
Without a network, a keyboard, or a monitor, controlling Raspberry Pi becomes a problem. I accidentally saw an article today.ArticleThat is, you can directly control the Raspberry Pi through the serial port. Give a decisive try. The effect is good. Share it with others!Pai_^ Preparation
board, some said to buy the PRC 2706 USB DAV sound card, about 50RMB, investment is not small.
Here are 2 proposals
Scenario 1, if you bought a Raspberry Pi 3 motherboard bought HDMI VGA interface line, then you are lucky, directly to the HDMI interface to the Raspberry Pi
The first blog gave me a long course design, that is, the topic "3G wireless router. The development platform used in this development project is the Raspberry Pi Development Board. The following is the question .....
Objective: To set Raspberry Pi as a 3G wireless router an
As small as you can't imagine a computer with a USB flash drive sold by Raspberry Pi _ love alive evolife.cn
As small as you can't imagine Raspberry Pi selling USB flash disks
Date: 17:58:26
Author: AI live temporary worker
Source: aliyun.com
Comment (3)
The ever-changing speed of technology is far be
, the monitor can use its own, I have a desktop monitor, bought an HDMI to VGA port line, you need to purchase according to their actual situation.Two: Install the Raspbian system.This is the official website system, the first time you can consider installing this, and then slowly.Install under Windows:1, download Raspbian system, B + board available system can be downloaded here (if the earlier system may not recognize the peripheral), download at th
program, please visit the blog: https://www.cnblogs.com/lulipro/p/5992172.html
This experiment was first tried in a new field and has never previously been approached by Raspberry Pi based program development. At first, there were a lot of problems: 1. The Raspberry Pi system burned incorrectly, and it wa
Prepare
Raspberry Pi Development Board ( Click here to purchase ) (has been brushed into the official Raspbian system )
USB to Serial board ( click here to buy )
DuPont Line (4 root)
Connection
串口板 树莓派--------------------VCC +5V(非必须)RX TXD(GPIO15)TX RXD(GPIO14)GND
Recently the classmate sent a Raspberry Pi, including an already packed Raspberry Pi Board (the Raspberry Pi box needs to be purchased separately), a power supply, and an SD card with a
One: Perform an upgrade on the Raspberry Pi:
1 : Updating the software source
$ sudo apt-get update
2 : Replace the old package
$ sudo apt-getupgrade
3 : Perform a Raspberry Pi firmware upgrade:
1, Raspberry Pi firmware: Can be
a more complex input with timing. Here are two points to note: The SetMode is in BCM mode, and the pin used is the same as the BCM number corresponding to the pin graph. You can also set the physical PIN number to use SetMode (GPIO). BOARD). The input/output mode is input when receiving data/status relative to host or Raspberry Pi, output i²c
I²c can be a bus to
-linaro-arm-linux-gnueabihf-raspbian-x64 are used for 64-bit machines.
Each cross-compilation tool has a bin directory in the directory to enter, execute./arm-linux-gnueabihf-gcc-v to view the GCC version.
I use ARM-RPI-4.9.3-LINUX-GNUEABIHF here because the GCC version on the board is now 4.9.3 3. Start compiling
3.1 Enter the Linux kernel directory:
$ CD ~/RASPBERRY/LINUX-RPI-4.4.Y
$ kernel=kernel7
$ make
SD Formatter, select the your SD card and format it.
DRAG and DROP NOOBS FILES
Once your SD card have been formatted, drag all the files in the extracted NOOBS folder and drop them onto the SD card Driv E.
The necessary files would then is transferred to your SD card.
When this process had finished, safely remove the SD card and insert it into your Raspberry Pi.
First BOOT
Environment: Raspbian-stretch (2018-06-27)Raspberry Pi: 3 generation B Type1, Raspberry Pi equipment, need to be in the field can also have independent networking capabilities, it is necessary to use the Internet of Things module.The SIM868 communication module for micro-snow is used here, such as:2, will SIM868 insert
purposes it is enough and has a very high price/performance ratio.
The software for receiving and decoding S-mode signals provides a site interface based on Google maps and a local display that is not particularly needed. However, the addition of the Adafruit PITFT 3.5-inch display (124-5487) provides a concise overview of the "at-a-glance" aerial activity. In addition, the combination of the Raspberry Pi
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.