isa motherboard

Into the system blue screen, heavy installation system is also this phenomenon, into the PE will be computer blue screen, into the PE is a screen, we often do memory or graphics card problems, but replace the memory and video card, into the PE system or blue screen. If it is a motherboard problem often this kind of problem is more difficult to check, because it is often related to hardware problems resulting in a blue screen driver. After inspection

The computer motherboard has broken down cause analysis: (1) The jumper is plugged in incorrectly. Of the 5 jumpers to be plugged in, there are 2 (hard drive lights, reset lights) that have polarity, if this is reversed, will burn the motherboard or hardware. (2) If not careful, when installed, some metal did not notice good, hanging on the motherboard, when th

What about the computer motherboard? A notebook after the water, must immediately power off forcibly shut down, dial the battery. The shutdown here is not to let you slow down the mouse from the Start menu, slow down a little notebook damage will be larger. After the dismantling of the motherboard, keyboard, etc. into the liquid easily damaged parts. To be completely removed from the

a8-7600 with what motherboard? To understand this issue, the main need to understand the AMD a8-7600 processor what kind of CPU slot, familiar with the desktop AMD processor friends or access to information, you can sort out this processor the following information. A8-7600 is AMD launched last year, a third generation Apu processor, based on socket fm2+ interface, the default frequency 3.1GHz, with 4M two level cache, built-in R7 core graphics card

North Bridge is the most important component of the motherboard chipset, also known as the main span. Generally speaking, the name of the chipset is named after the North Bridge chip, for example, the North Bridge chip of the Intel 845E chipset is the North Bridge chip of the 82845e,875p chipset is 82875P and so on. North Bridge Chip is responsible for the connection with the CPU and control memory, AGP data in the North Bridge transmission, to prov

Motherboard temperature overheating Reason analysis: For the main board of heat, nothing more than the north-south Bridge, treat these guys we can use the replacement of the radiator method. For example, overclocking three or nine state and so on high quality brand products. If you replace the motherboard heatsink, the motherboard temperature is still too high

Generally, Intel has two EHCI and one xhci on the motherboard that supports USB 3.0 host controllers. This type of motherboard generally has 14 ports, and port 0-3 is shared by EHCI and xhci, that is, port 0-3 has four switches, and the control registers of these four switches are located in the xhci PCI (PCI-E) configuration space, the four switches on the PC are configured in the BIOS. Because many boards

gaps, single-side 84-pin, double-side 168-pin, voltage 3.3 V, memory rectangular (obsolete ). 2. ddr1 (First Generation) one notch, single side 92 pins, double side 184 pins, voltage 2.5 V, memory particle rectangular operating frequency 266,333,400. 3. DDR2 (second generation) one notch, single side 120 pins, double side 240 pins, voltage 1.8 V, memory particle square operating frequency 533,667,800. 4. ddr3 (Third Generation) one notch, single side 120 pins, double side 240 pins, voltage 1.5

"SerialNumber",Motherboard serial Number"SELECT * from Win32_baseboard where (SerialNumber are not NULL)",L "SerialNumber",Processor ID"SELECT * from Win32_Processor where (Processorid are not NULL)",L "Processorid",BIOS Serial Number"SELECT * from Win32_BIOS where (SerialNumber are not NULL)",L "SerialNumber",Motherboard model"SELECT * from Win32_baseboard where (Product was not NULL)",L "Product",Network

Motherboard SATA connector does not recognize the hard drive reasons and solutions: One, the hard disk can not use the fault 1, BIOS setup Error Mainly in the BIOS on the SATA Setup error, especially some early motherboards using a Third-party sata/raid control chip, but basically in the BIOS is closed, so to use the hard drive, you need to open this chip. 2, SATA connector failure There are 2 possible types of failure: 1 joints loose, the pheno

accidentally touched the built-in modem yesterday, and I don't know where it fell ...". The author picks up the motherboard instruction book, looks for inside with the jumper related explanation. In the Sound card settings page suddenly see this: "If you do not want to use the front audio, 5, 6, 9, 10 must use jumper short, so the signal will be output to the back of the audio interface." Originally this MSI mot