juniper switch configuration commands

4R1 (config-line) # exec-timeout 5 2 The Huawei Switch configuration is based on the permission level set on the device: R1 (config) # privilege configure level 3 usernameR1 (config) # privilege configure level 3 copy run startR1 (config) # privilege configure level 3 pingR1 (config) # privilege configure level 3 show runR1 (config) # enable secret level 3 cisco The basic command privilege for configuring

LAN switches have evolved from a HUB-based LAN shared in the traditional sense to a broader space. Take Cisco's Catalyst 5000 Series LAN switch as an example. It includes an integrated switching hardware structure, 10-Mbps Ethernet that supports switching, and-Mbps Fast Ethernet, supports fast Ethernet, FDDI, exchange-type ring, and layer-3 switching processing. This type of switch can provide exchange acce

1 , what is the privileged mode of the switch? There are 6 modes of the switch. 1: The user execution mode (userexecmode). 2 : Privileged Execution Mode ( privilegedexec Mode ). 3 : Global configuration mode ( globalconfiguration Mode ). 4 : Monitor mode ( ROM Monitormode ). 5 : Safe Mode ( Setupmode ). 6 : Boot Mode ( Rxbootmode ). commonly used to have the a

Configure Span dialog (span session) Basic functions By setting the span dialog to monitor the data flow of the switch port or the entire VLAN, the monitored data stream can be analyzed and processed by the Protocol analysis device. Working mode The span dialog consists of a destination port and a set of source ports that replicate packets from one or more source ports on one or more VLANs to the destination port. span does not affect the normal o

interface that will be configured as a three-tier interface Step 3 No Switchport To get the physical interface into layer three mode Step 4 IP address ip_address subnet_mask Configure IP addresses and subnet masks Step 5 No shutdown Step 6 End Return Privileged Mode Step 7 show interfaces [Interface-id]show IP interface [Interface-id]Show Running-config interface [Interface-id] Confirm

Overview of LAN switches LAN switches have evolved from a HUB-based LAN shared in the traditional sense to a broader space. Take Cisco's Catalyst 5000 Series LAN switch as an example. It includes an integrated switching hardware structure, 10-Mbps Ethernet that supports switching, and-Mbps Fast Ethernet, supports fast Ethernet, FDDI, exchange-type ring, and layer-3 switching processing. This type of switch

I have just been familiar with the basic configurations of the VLAN division experiment of the switch VLAN division configuration (PT simulator). I am not familiar with this knowledge for too long. Please forgive me for any errors, this configuration is for you to learn about the Cisco simulator configuration case. Www

bound IP and Mac (2) 1 port next to a small switch binding mode such as: 1th ports under a 8-port access to a small switch, the switch has 3 computers, 3 computer IP and Mac as follows 1 Computer's ip:10.100.11.2 mac:00-1a-4d-1e-39-812 computer's ip:10.100.11.3 mac:00-1a-4d-1e-39-8e3 computer's ip:10.100.11.4 mac:00-1a-4d-1e-39-8f So these three computers ne

/ theunassigned YES unset up GigabitEthernet1/ -unassigned YES unset down GigabitEthernet1/ -unassigned YES unset down GigabitEthernet1/ -unassigned YES unset down GigabitEthernet1/ +unassigned YES unset down GigabitEthernet1/ -unassigned YES unset down GigabitEthernet3/1unassigned YES unset up GigabitEthernet3/2unassigned YES unset up GigabitEthernet3/3unassigned YES unset up GigabitEthernet3/4unassigned YES unset up GigabitEthernet3/5unassigned YES unset up GigabitEthernet3/6unassigned YES uns

trunkSwitch (config-if) #switchport trunk allowed VLAN, set allowed VLANsSwitch (config-if) #switchport trunk encap dot1q; set VLAN trunkingSwitch (config) #vtp domain; Set the VTP domain nameSwitch (config) #vtp password; set the VTP passwordSwitch (config) #vtp mode server, setting the VTP patternSwitch (config) #vtp mode client, setting the VTP patternSwitch set IP address:Switch (config) #interface vlan 1; go to VLAN 1Switch (config-if) #ip address; Set IP addressesSwitch (config) #ip defau

Super [command] super [level] [view] www.2cto.com user view [Default level] 0: access level [parameter] level: user level, value Range: 0 ~ 3. The default value is 3. [Description] The super command is used to switch the user from the current level to the specified level. 1-9 if the level parameter is not specified when using this command, the user will switch from the current level to level 3. User level r

restarting the masterha_manager service.II. Server description 192.168.10.103 masters // master192.168.10.209 slave1 // from192.168.10.219 slave2 // slave (master/slave)192.168.10.220 manage // management nodeOne master, two slave, and one management node write the content above to each/etc/hosts.3. Password-less ssh login between servers # Ssh-keygen-t rsa# Ssh-copy-id-I/root/. ssh/id_rsa.pub root@192.168.10.103# Ssh-copy-id-I/root/. ssh/id_rsa.pub root@192.168.10.209# Ssh-copy-id-I/root/. ssh

In the work encountered H3C and HW RRPP configuration, the following is the Huawei simulator to do another experiment. We all come together to discuss the problems encountered. "Theoretical basis" RRPP specific theory See configuration Manual Here are just a few things that are prone to error. 1, as the RRPP loop interface to close STP 2. Two IMPORTANT commands