kali linux vpn

Use of the "Dig" command:Dig is the domain name resolution tool in Linux, the function is much stronger than Nslookup, and it is very convenient to use. The use of dig under Windows system must be downloaded and installed.How to use:[Email protected]:~# dig www.cnblog.comFor a description of the various logging resources in DNS, please refer to: http://bbs.51cto.com/thread-909189-1.htmlFind a record of the blog park:Find a list of MX records for the b

After the Kali Linux installation is complete, its network needs to be configured. Using a DHCP service is one of the easiest ways to configure a NIC, but it is not usually done when penetration testing because the system is logged in the DHCP server's database.1 Dynamic DHCP modeConfiguration file Address:/etc/network/interface# Start System activation device# Loop loopback AddressAuto LoIface Lo inet Loop

Tags: alt system directory Virtual disk pretty upd Aliyun dependency update1. Edit the source.list in the Etc/apt file.Edit Source.list----->vi/etc/apt/sources.listReplace the original system comes with the source of the file, the online find of Ali's replacement as follows;Deb Http://mirrors.aliyun.com/debian wheezy main contrib non-freedeb-src Http://mirrors.aliyun.com/debian wheezy main Contrib Non-freedeb Http://mirrors.aliyun.com/debian wheezy-updates main contrib non-freedeb-src/HTTP Mirro

Experimental environment: (1) The company all game servers, only allow an extranet IP to access, need to maintain the server, must first dial to the designated extranet IP. (2) The company and headquarters communications are to take the VPN channel, the company's internal IP and VPN devices are different network segments, need to be under the VPN device to conn

That's what happened.Want to install a software that generates a password by personal information this morningFound unable to installAfter the problem is discoveredI first checked the Kali there was no access to the IPAnd then there's no IP access.How to solve the problem is as follows:Principle Process:1. Writing to the DHCP service1. Make DNS settingsEnter the command first: Gedit/etc/network/interfaces #用gedit进行编辑Under Iface Lo inet loopbackWhat to

VPN client on linux debian, vpndebian Install the pptp-linux and pptp-linux-client: 1 sudo apt-get install pptp-linux-client Create a connection config: 1 sudo pptpsetup -- create [ConnectionName] -- server [Ip] -- username [Username] -- password [Password] -- encrypt

My Vyatta operation has been very good, with Ros and Cisco do tunnel connected to Vyatta run OSPF used to turn the wall, the effect has been good. When you use Windows to connect to a VPN, however, you often open the page timeout, but the ping is normal everywhere, so you suspect an MTU or MSS problem. After several twists and turns, when the Web page timed out, a large number of exceptions occurred in the Vyatta log: 21:02:39 Xirang kernel: [483817

By step: Operating Environment Centeros 6 * First run the following command: cat /dev/net/tun The return must be:Cat:/dev/net/tun:file Descriptor inRun:cat /dev/pppThe return must be:Cat:/dev/ppp:no such device or address If the above return is not the result of these two, please contact the VPS Customer service to open PPP and Tun permissions. ################################################@1--Install PPP Yum install gcc yum Install PPP @ Remember to load GCC @2-----Install

In Linux, any software accesses the Internet through proxy (non-vpn). in windows, SocksCap32, ProxyCap, FreeCap, and Proxifier can access the Internet through proxy. This blog has previously introduced: http://www.2cto.com/net/201207/142900.html ,... In Linux, any software accesses the Internet through proxy (non-vpn).

be done using the skb_copy_expand function. Fill in the ipip header field after the allocation. At this point, most of the logic of the ipip protocol has been clearly described. The following is a function value note. Static int This function is the place where the application interacts. To put it bluntly, it is the place where the Linux system commands ifconfig and IP commands are used as an excuse, creating tunnels, deleting tunnels, changing IP a

VPN Client Connection Linux server access slows down how to solve There are three ways to solve the problem: Method One: Edit pptpd source code, increase MTU; Method Two: Use a script to increase the MTU after the PPTP interface is connected to the up; Method III: Do not use MPPE encryption; The first, although fundamentally solves the problem, but because the level problem gives up; the third becaus

Most of the logs for logging on to the linux pptp vpn user name pptpd are stored in files such as/var/log/messages,/var/log/daemon. However, after careful reading, the user name is not found in the logs, I don't know which account the user used to log on. So I looked at pppd man and found some environment variables, such as IPLOCAL and IPREMOTE. After testing, I found that PEERNAME is the user name, in this