Iwconfig
Iwconfig is one of the User-layer configuration tools of wirewirelessextensions (LWE. LWE is a tool for wireless network configuration in Linux, including Kernel support, user-layer Configuration tool, and Driver Interface Support. At present, many wireless network cards support LWE, and mainstream Linux versi
In Linux, the wireless network card is used to set up an AP. Due to the need of the experiment, we need to set up a Wireless AP. After a long time, we finally finished the setup. Www.2cto.com my machine is equipped with two NICs, the wired Nic is connected to the network through the network, and there is also a wireless
iwlist wlan0 scan
From: http://linux-wiki.cn/wiki/%E6%97%A0%E7%BA%BF%E7%BD%91%E5%8D%A1%E9%85%8D%E7%BD% AE
This article describes how to manually configure a wireless network card on the Linux command line interface. Currently, most popular releases support convenient configuration with the network-manager graphical interface, without the original method describe
assigning an address to the bridge port, you can configure the Gateway as the bridge port address for other subnets. Of course, because the device is in the Gateway mode, routing and nat are also required. If the device is in the bridge mode, the routing and nat can be saved.
Brctl addbr bridge
Brctl addif bridge eth0
Brctl addif bridge ath0
Ifconfig eth0 0.0.0.0
Ifconfig bridge 10.0.0.1 netmask 255.255.255.0 up
Add iptables-t nat-a postrouting-o eth1-j SNAT -- to 192.168.2.173
Set both wir
If you are learning about Linux, you have installed Linux on your computer, but you often need to access the Internet. There is no wireless network adapter in Linux, here we will introduce you to the installation of the DWL G122 driver module for the
By Sreekrishnan Venkateswaran
Linux Bluetooth
Bluetooth is a short-range wireless technology used to replace cables. It supports 723 kbps (asymmetric) and 432 kbps (symmetric) speeds to transmit data and voice. The transmission range of a Bluetooth device is about 10 meters (30 feet ).
BlueZ is the official Linux Bluetooth Stack. It consists of the Host Control
Linux wireless NIC Driver-Linux general technology-Linux technology and application information. For more information, see the following section. Recently, the school started wireless networks, and ECHO also integrated three NETGEAR wire
The general idea of linux wireless network card command configuration is as follows: Use iwconfig to enable the power of the wireless network card, and find the wireless network in the region to connect to the corresponding wireless network www.2cto.com to enable the
upAdd iptables-t nat-a postrouting-o eth1-j SNAT -- to 192.168.2.173Set both wired and wireless to the 10.0.0. * CIDR block to allow access by network peers.Of course, if Linux can work in the bridge mode, you must install the bridge-utils tool and run the following command:Yum install bridge-utilsDownload bridge-utils-1.4.tar.gz to install bridge-utils-1.4.tar.gz. The steps are as follows:Compile and inst
The method for using cdma wireless Internet access in linux-Linux general technology-Linux technology and application information. The following is a detailed description. I'm glad I finally got online. Step:
Dmesg | grep tty check whether your wireless network
Article title: wpa wireless network configuration in linux. Linux is a technology channel of the IT lab in China. Includes basic categories such as desktop applications, Linux system management, kernel research, embedded systems, and open source.
First install firmware. my wireles
Since it is a technical activity, you will keep up with me so that you can immediately know howLinuxUseBluetoothCreate a wireless network.
The ip address wireless network under the Bluetooth is called pan. The Bluetooth device highlights the link between the individual and the electronic device, and the use of personal is also good. Like the general network that we use, there are also clients, router, and h
: Access Point (AP)Ad-hoc: Only in this mode, the device can be a multi-hop network (mesh network) with devices in other AD-HOC modes, which requires some wireless Ad-hoc routing protocols, such as the famous Batmand protocol.Monitor: Only in this mode, the NIC can listen for frames from other devices on the same channel. You can get the address, content, RSSI (even channel state information) for these frames CSI, theoretically, actually, according to
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.