mount filesystem

When you have bind mount the option of the command, you must is sure that the file systems is mounted in the correct Orde R. In the following example, the /var/log directory must is mounted before executing the bind mount on the /tmp directory: Mount --bind/var/log/tmpThe ordering of file system mounts is determined as follows: In general, file system

00First list device: Disk device file or label or UUID for the device1) View the label and UUID of the partitionLabel is the label of the partition, in the initial installation of the system is filled with the mount point is the name of the label. You can find the UUID and label name by looking at the information in the superblock of a partitioneg[[email protected] home]# dumpe2fs-h/dev/sdb1 #查看 virtual machine New second hard drive/dev/sdb1 dumpe2fs

Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632 Writing Inode table: complete Creating Journal (32768 blocks): complete Writing Superblocks and FileSystem accounting information: Complete This filesystem would be automatically checked every mounts or Whichever comes first. Use Tune2fs-c or-i to override. So it's formatted so that we ca

the device that needs to be mounted, and the/hda2 is the second partition of the primary hard disk on the first IDE slot. If the second IDE slot is the third partition of the primary hard drive, it is/DEV/HDC3, which can be viewed under Linux using Fdisk-l.(2) Mount pointMountpoint is the mount point. /,/usr, swap are the default mount points for the partition w

created four primary partitions, then the partition will have the following prompts: Command (M for help): N youmust Delete some partition and add an extended partition This requires that you first delete a primary partition, and then create an extended partition, which is a place to note that if you are creating a primary partition that is larger than four when you create a partition plan, you will need to create an extended partition to meet your planning needs when you create three primary p

version information for the mount. Device the partition or file to be mounted. If device is a file, the-o loop parameter must be added when mounting. The mount point of the Dir partition. Appendix 4:fstab Configuration Detailed | Appendix Part 4:fstab Detail Configuration/etc/fstab A total of 6 columns:File system: Specifies the device name (for example,/dev/sdb) of the

Recently, I finally installed a linux server in my company. The linux system installed was CentOS6.3. during the installation, I did not cover the partitions of Windows2003, but I just allocated a small disk (4 GB) partition swap, and then allocate GB to/partition. The NTFS partition cannot be mounted after the installation is successful. The mount error "mount: unknownfilesystemtype 'ntfs Recently, we fina

after 21 mounts or 180 days, using TUNE2FS-C or-I can override the default automatic check. Anyway, I don't need the system default check what, then I just shut it down, and use it to suggest the TUNE2FS command is good. [root@~]# tune2fs-c 0-i 0/DEV/SDB1 #-C and-I are followed by 0 (not checked), or disk partition file ~ ~tune2fs 1.41.12 (17-may-2010) Setting Maximal mount Count to-1setting interval between checks to 0 seconds#提示信息我就不逐条翻译了, whic

adjust the size of each partition without downtime.How to have a USB disk containing the LVM partition. I want to access these LVM partitions in Linux. How can I mount an LVM partition on Linux?In LVM, the physical storage that creates a logical partition is a traditional partition (for example,/DEV/SDA2,/DEV/SDB1). These partitions must be initialized to "physical volume PV" and labeled with a volume label (e.g. "Linux LVM") to enable them to be use

LINUX Mount USB CD share fileFdisk-l Viewing disksParted-l Viewing disksMount device file name mount pointMount/dev/cdrom/mnt/cdrom Mounting DiscsUmount/dev/cdrom Uninstalling DiscsMOUNT/DEV/SDB1/MNT/USB Mount USBUMOUNT/DEV/SDB1 Uninstalling USBMount-t cifs-o username= user name, password= password//192.168.0.102/share/mnt/share #

filesystem already exists on a partition on the hard disk (or similar device), and the kernel is directly mount based on the command line arguments (ROOT=/DEV/XXX) that are started. Here is a problem, kernel how to find the corresponding device according to/dev/xxx when the root file system itself does not exist. The original kernel by directly resolving the device's name to obtain the device's master, fro

As we said before, the mount point is the directory, and this directory is the entry into the disk partition. But before you can mount it, you'd better make a few things right:A single file system should not be repeatedly mounted in different mount points (directories);A single directory should repeatedly mount multipl

hard disk partition should be how to express. The first primary partition of the first disc should be "SDA1", the second primary partition of the first disk should be "Sda2", the first primary partition of the second disc should be "SDB1", and the second primary partition of the second hard disk should be "SDB2" and so on.4, it should be noted here that there are 4 primary partitions, and the extended partition as a special primary partition, the logical partition is built on the extended parti

In Linux, mounting exFat first refers to mounting a mobile hard disk in the exFAT format. Recently, a dual system, one disk is Windows 7, and the hard disk format is exFAT, if you want to access the files under Windows 7 in Linux, the following error occurs: mount failure. # Mount-t exfat/dev/sda2/mnt/d mount: unknown filesys