pcie development board

The. Net Micro Framework Official graphics library is WPF, because the current St CORTEX-M3 Development Board RAM is too small, the largest 512K (commonly 128K or 256k), and CORTEX-M3 CPU frequency is not too high, Running the WPF graphics frame is too heavy, so here I have a lightweight graphics library Tinygui (in addition, I also launched a WinForm framework that is compatible with the. Net framework and

accordance with AAC compression, and then write to the MP4 file, Because before this experience, so the earliest use of wince default WMV9 soft code, the result of less than 10 seconds compressed, the machine died. At first thought it was their own code did not write correctly, many attempts, basically toss for a week, and finally found that the machine memory continues to fall until all eat, Then came the clear: on the small machine, the use of soft coded compressed audio and video data, basic

Just before a PDA with wifi features, so instead of using a PC to control the Smart car via ZigBee, it's more convenient to control it with a PDA, but since the. NET MF Development Board does not directly support WiFi, we have to control it indirectly, that is, PDA control pc, PC through ZigBee control intelligent car. For our developers, WiFi is the same as the normal cable interface, is the socket progra

modifying the above configuration file, save exit.6. Execute the command:Restart the Rpcbind service.7. Execute the command :#/etc/init.d/nfs-kernel-server RestartRestart the NFS service.# mkdir/mnt/nfs# Mount 192.168.1.101:/opt/friendlyarm/mini210/linux/rootfs_mini210/mnt/nfs# Ls/mnt/nfsArm Linux CmdLineRoot=/dev/nfs nfsroot=192.168.1.101:/opt/friendlyarm/mini210/linux/rootfs_mini210 ip= 192.168.1.102:192.168.1.101:192.168.1.1:255.255.255.0:linux.arm9.net:eth0:off INIT=/LINUXRC console=ttySAC

-boot.bin OF=/DEV/SDX bs=1024 seek=32# Sync# umount/mntand copy the Kernel modules for Partition 2 # MOUNT/DEV/SDX2/MNT# CD:# cp-a linux-allwinner/out/lib/modules/3.0.42+//mnt/lib/modules/.# umount/mntSo now you have an SD card ready to boot Debian.(now there is a SD card ready-to-boot Debian on A13-olinuxino.)Connect the USB to the serial port or VGA screen, insert the SD card into A13-olinuxino (-wifi), and power on, you should see the uboot and kernel information after the terminal. The defau

. Input, abs_x, 0, 0x3ff, 0, 0); Input_set_abs_params(ts. Input, abs_y, 0, 0x3ff, 0, 0); Input_set_abs_params (ts.input, abs_pressure, 0, 1, 0, 0); in the Touch_timer_fire function: Input_report_abs(ts. Input, abs_x, TS. XP); Input_report_abs(ts. Input, abs_y, ts. YP); Input_report_key(ts. Input, Btn_touch, 1); Input_report_abs (Ts.input, abs_pressure, 1); Input_sync(ts. Input); Input_report_key(ts. Input, Btn_touch, 0); Input_report_abs (ts.input, abs_pressure, 0);

This paper is from: http://www.topeetboard.com First configure the Kernel The kernel directory runs the command "CP config_for_ubuntu_hdmi. config", as shown in the following figure: Then execute "make" and start compiling the kernel, as shown in the following figure: Compilation completion generates MIRRORS: Zimage Modifying the Linux file system Go to our Linux file system, as shown below: Then use the command "VI Bin/qt4", as shown in the following figure: Then add at the beginni

cross-platform Compile) work. The current tool key software has realworks toolchain, GNU toolchain. Microsoft's Visual Studio 2005 is the toolchain of Windows CE. Cross-compilation (cross compile) is a common way to compile programs on one platform that can run on a different architecture, such as compiling on a PC platform (X86 CPU) to Programs running on an arm-based CPU platform, compiled programs that are not operational on the X86 CPU platform, must be placed on the ARM CPU

Big Three are: Uboot, kernel and file systemCommunication: USB OTGNote : The burn-write is implemented in the CMD console in the folder where the FastBoot is located, not the serial terminal HyperTerminal. Copy the files you want to burn into the FastBoot folder. fastboot.exe Flash bootloader u-boot-itop-4412.bin " Flash: Execute burn write bootloader: Burn write type u-boot-itop-4412.bin: Burn Write Object " fastboot.exe Flash kernel zimage "This command is used to burn the kernel (kernel)

ArticleDirectory Sorry, it's been too long for everyone to wait. The upgraded black gold Development Board can finally meet you. According to your needs, I have made constant changes to it, so the longer the time is, the more I believe that it is worthwhile to use this time to wait for an upgraded version of the black gold Development

650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M02/49/40/wKiom1QRa6vzFT2kAAGAGH3HjVc121.jpg "Title =" real210v6.2.jpg "alt =" wkiom1qra6vzft2kaagh3hjvc121.jpg "/> 650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M00/49/42/wKioL1QRa8qjDJdPAAEhOIPeexc452.jpg "Title =" 7inch capacitive screen .jpg "alt =" wkiol1qra8qjdjdpaaehoipeexc452.jpg "/> The latest, most powerful, and most complete real210 Development

Thanks for the hard work, we finally finished the NFS network. First, the computer and the Development Board need to be connected to the router to form a LAN (I ignored this ...) PC: Ubuntu 12.04 Development Board: Linux 2.6.32.2 click to view Ubuntu to burn Linux TO THE DEVELOPMEN