php imap

prepare an article 1, configure the firewall, open 80 ports, 3306 portsVi/etc/sysconfig/iptables-A input-m state--state new-m tcp-p TCP--dport 80-j ACCEPT #允许80端口通过防火墙-A input-m state--state new-m tcp-p TCP--dport 3306-j ACCEPT #允许3306端口通过防火墙 Note:

1, configure the firewall, open 80 ports, 3306 ports Vi/etc/sysconfig/iptables -A rh-firewall-1-input-m state--state new-m tcp-p TCP--dport 80-j ACCEPT -A rh-firewall-1-input-m state--state new-m tcp-p TCP--dport 3306-j

First, install and configure MySQL 1.1 Execute Yum command to install MySQLYum-y install MySQL Mysql-server 1.2 Add MySQL to boot and start MySQL immediatelyChkconfig–levels 235 mysqld on/etc/init.d/mysqld Start 1.3 Set the MySQL root account

The example in this article describes the way PHP gets mail based on IMAP. Share to everyone for your reference. The implementation methods are as follows: IMAP is a mail interactive access protocol, the following is an example of the main use of

Lamp is LInux, APache, MYsql, PHP's abbreviation. This tutorial will teach you how to install Apache2web server +php (mod_php) +mysql on a Fedora 12 server. I have tested it correctly and you can use it safely. 1. Foreword In this tutorial, I

Describes how to use the Yum configuration installed under the CentOs6.2 lamp environment, some brothers also like to use the installation method of compiling, personal feel if not to the server to do custom, with Yum installation stability simple,

2011-10-31 12:44 because the Linux default Yum source is installed with PHP 5.1 package, Yum Install php view later Rpm-qa PHP Php-5.1.6-23.2.el5_3 because some programs need to use the version above php5.2 so I found the information, finally

RH9 with a PHP written webmail, can provide based on the SendMail Mail Web interface, the configuration method is also very simple, everyone as long as I follow the steps below, you can easily build a Web mail server for yourself (about 10 minutes

Yum Build LNMP Environment (CENTOS6)1. Turn off the firewall[Email protected] ~]# chkconfig iptables off2. Turn off SELinuxVi/etc/sysconfig/selinuxModify selinux=enforcing to disabled and then restart to take effect3. Configure CentOS 6.0

Recent projects made in PHP to the project deployment, the server for the centos6.4 system, in order to quickly deploy, the use of Yum installation deploymentMost of the Content reference blog

Prepare the article:1, configure the firewall, open 80 ports, 3306 portsVi/etc/sysconfig/iptables-A input-m state--state new-m tcp-p TCP--dport 80-j ACCEPT #允许80端口通过防火墙-A input-m state--state new-m tcp-p TCP--dport 3306-j ACCEPT #允许3306端口通过防火墙Note:

/* 1. First solve the Internet 1-1. Refer to the Networked status file # cd/etc/sysconfig/network-scripts # vi ifcfg-eth0 1-2. Edit the Networking form See figure 1-2 1-3. Restart Network # service Network Restart | /etc/init.d/network Restart 2.

All of the following are reproduced in http://blog.csdn.net/lane_l/article/details/20235909I followed this article tonight using the CentOS 6.7 64bit installation successfully, make a backup, and then turn around.-------------------------------------

CentOS 6.5 Installation Configuration Lnmp server (nginx+php+mysql)I. Preparation of the article:1/etc/init.d/iptables stop#shutting down the firewall2 Turn off SELinux3vi/etc/selinux/Config4 #selinux=enforcing #注释掉5 #selinuxtype=targeted

Environment: CentOS Release 6.7 (Final)Installation software: nginx+mysql+phpInstallation Tool: Yum1. Install Nginx, because the default Yum base source is not nginx, so this way to add Nginx official source to the local1) Address:

prepare the article: 1, configure the firewall, open 80 ports, 3306 portsVi/etc/sysconfig/iptables-A input-m state--state new-m tcp-p TCP--dport 80-j ACCEPT #允许80端口通过防火墙-A input-m state--state new-m tcp-p TCP--dport 3306-j ACCEPT #允许3306端口通过防火墙 Note:

Linux Network configuration First Use: ifconfig check the network cardIf you have only one L0 NIC, you need to open a eth0 network cardTurn on/off network card: ifconfig NIC name Up/downEg:ifconfig eth0 up #打开eth0网卡Configure IP Address:

This article mainly describes the CentOS 6.4 configuration Lnmp Server detailed steps, the need for friends can refer to the followingPrepare the article1, configure the firewall, open 80 ports, 3306 portsVi/etc/sysconfig/iptables-A input-m

Process record of setting up Apache+php+mysql environment under Docker This is a process record for setting up a Docker environment for easy viewing later. The main records are the tools used to build, the commands used and the pits

Gitlab is better than SVN, ready to use Gitlab+redmine and move the code to Gitlab.Machine IP 192.168.1.146System CentOS 7.1 one. Gitlab installation This time using the Yum installation method, the compilation and installation has not been