qualcomm development board

I have used the mini2440 Development Board-General Linux technology-Linux technology and application information. The following is a detailed description. I have an old mini2440 board with 64 MB memory. now I have loaded the 2.6.32 Linux kernel (using a new light disk on the Internet) according to the instructions ), however, I encountered a problem when compilin

instructionsFunction: Cache pre-read (Pld,preload), using PLD to instruct the storage system to read from the memory address specified in the following instructions, the storage system can use this method to speed up future memory access.Workaround: Modify the MPLAYER-1.0RC2/LIBMPEG2/MOTION_COMP_ARM_S.S and MPLAYER-1.0RC2/LIBAVCODEC/ARMV4L/DSPUTIL_ARM_S.S the two error files, On the previous add:#ifndef HAVE_PLD. macro PLD Reg. endm#endifand make it again.(4) Cross-compile to generate executabl

Now I have a UT-6410 V1 to shot, was bought back to test whether there is a market, Just boot a few times, huh, huh. The official offer is 3500 RMB, I will offer a discount, and buy UT-6410 V1 to send a fl2440 Development Board + jlink V8 + multi-purpose conversion interface-the Board confirmed that can use jlink. Haha It's fierce enough, hahahahaha. It is also

development version of the feeling, and some effects on the display. (Boot configuration What I do not say, if you are interested in buying this development version, the instructions are already very clear, it is easy to get started, I configured it took a total of 5 minutes). The Development Board built a small demo,

Use of the environment: Win7 flagship 64-bit, VMWARE11 using the ubuntu12.04 provided on the board to open the virtual machine directly with VMware, since the development of the epc9600 Development Board, so the virtual machine network has been set, load ubuntu12.04 after the discovery can be directly networked .The cr

commands such as Snmpd,snmpwalk with the Arm-linux-strip command before porting9. Copy the Snmpd,snmpwalk to the Development Board/usr/bin, snmpd.conf and MiB folder and folder contents to the Development Board/usr/local/share/snmp/No folders created by yourself, note using chmod 777 Snmpd,snmpwalk10. Running snmpd-cc

CalibrationThe second correction process is DQS gating calibration. It is used to fine-tune the read DQS gating so that it can accurately capture the read DQS signal. The calibration program adjusts the DQS gating delay to find a valid DQS delay window in the 4/256-always cycle. Press ' y '/' n 'Intermediate operation similar, no longer translated Calibration ResultsAfter finishing all the calibration process, the calibration results is summarized and as shown below.? The tool would proceed to

Http://www.analogcn.com/news/wd/200711/20071121171437.html The Manual on the bf531 Development Board is a bit hard to understand:I am confused when I use the Super Terminal FTP on Windows PC and Linux PC FTP later.The manual says:(1) You must first transmit the program FTP to the Linux server.Which server is it uploaded? How can I get the username and password? Please tell me one. (2) After FTP is downloa

Generally, developers in development companies have different development boards at the same time because of Project iteration requirements. However, the USB of different development boards is different, which makes the adb unidentifiable. The following is a solution for Ubuntu. Step 1: Open the terminal and enter the usb id of our new

The previous article introduced the Http Server and accessed the Http service on the Development Board through the IE browser on the PC (equivalent to the Http client. This time, we implemented the Http Client on the Network Development Board to obtain weather information on the Yahoo website and display the informatio

Compile the Linux kernel of the NanoPi2 Development Board and nanopi2linux Compile the Linux kernel of the NanoPi2 Development Board. 1. Download The Linux4.4 kernel source code Git clone https://github.com/friendlyarm/linux.git // these steps need to be used in a linux environment, the download speed is slightly s

/wKiom1cy3v3SjVNEAABq49zVkfU338.jpg "title=" Picture 8.jpg "alt=" wkiom1cy3v3sjvneaabq49zvkfu338.jpg "/> If the input file address, as you u-boot-itop-4412.bin the actual address of this file, the of the output address, the actual device number of your TF/SD card is subject to.Here, you can insert the TF/SD card into the Development Board to power up, in order to prove that we are burning, we do the followi

MiS603 Development Team Date: 20150911 Company: Nanjing mi Lian Electronic Technology Co., Ltd. Forum: www.osrc.cn Website: www.milinker.com Shop: http://osrc.taobao.com Eat blog: http://blog.chinaaet.com/whilebreak Blog Park: http://www.cnblogs.com/milinker/ MiS603 Development Board the Fifth Chapter button to shake the experimentThe chattering of the keys means

input conversions, or 1 if an error occurs, otherwise 0 is returned;Iconv_close is to close the pipe (channel).If for a large number of encoding needs to be converted, the above function covert is not suitable for this way, one is the memory limit can not be called once, second, if multiple calls will frequently open a coded pipeline (channel), resulting in waste of resources, the best way is to take apart the function according to the situation use.Second, arm-linux transplant process1) http:/

First, install, configure, start FTP, SSH, or NFS servicesRefer to Vedon's complete manual for embedded Linux application development http://pan.baidu.com/s/1o79h3n0Second, Windows, Linux, and the Development Board need to ping the threeReference: Http://pan.baidu.com/s/1o8Uw0voNote: The Development

To modify the IP address of the arm Development Board, if it is a yaffs2 file, you can 1. First, modify the/etc/init. d/RCS file in/sbin/ifconfig lo 127.0.0.0. Add one/sbin/ifconfig eth0 192.168.1.20 up Note: 192.168.1.20 is just an example. You can change it to the IP address you want to modify. I can do this after modification, but I found that it still does not work. Using the ifconfig command, I fou