Design of power supply in high-speed circuitThe design of power supply in high-speed circuit is probably divided into two kinds, one is lumped architecture and one is distributed architecture. A lumped architecture is a power input that generates a variety of required voltag
to the auxiliary circuit. I suddenly realized that there was something wrong with the auxiliary power supply? The biggest difference between ATX power supply and at power supply is that it provides an auxiliary
is that the power supply is insufficient.
2, the use of substitution, replaced by a good chassis power supply test, found that the fault still exists, prove that the power supply is not a problem.
3, so
charging wire uses PVC plastic skin
The plastic skin of the charging line is likely to wear seriously, weathering chap and so on during the daily use, it will leak out the internal metal wire, which is likely to cause short circuit. Where the wire is welded with the circuit board and the electric core, usually also use insulation tape for fixed and other measures to deal with, but in some inferior products have not been such treatment, will solder j
Generally speaking, when the computer is working properly, the sound is very small, in addition to the hard disk read and write data emitted by the sound, mainly the cooling fan sound, especially the switching power supply fan emits the loudest. Some switching power supply after long-term use, in the work will produce
mainly applicable to the touch switch.3. sys_pwr_hold power supply is maintained, which is effective at a high level. It is useful when you touch the switch or the system wants to control the shutdown.Typical applications:1. the power switch uses the touch switch to detect the pwr_key_det status and control sys_pwr_hold. This enables the system to start up, hold
instability of the reason is directly caused by the power supply. Check the power before we should first consider whether the computer has been added cards and other accessories, some brand-name machine power and the total power of the system is exactly the same, add a new
Power Management Module ( PMM ) and power supply monitoring introductionPower Management Module and supply Voltage SupervisorI think power management and monitoring is a very complex and difficult to control part, not only involvesThe choice of source mode involves complex i
If you use your mobile phone with the data line charge can not be charged, please replace a can only charge can not transmit data microUSB line to try, this may be mobile charger in the electricity transmission to the phone.
You can try to connect other phones to the mobile power supply to see if there is a situation where the electricity can not be recharged into the phone, and if not, it could be a phone
The cause analysis and solution of the power supply light of notebook computer is not bright/flashing continuously
One, the power light is not bright
First of all, The notebook power light is not lit, there are two situations:
If the LEDs on the external power
Are you going to have a power supply to get him powered on without a motherboard?
The ATX 20pin has a non-stop bayonet on it, and it's facing itself, and then it's down to the left of the line. 4th and right, 4th, get these 2 connected.
Green and any one black, black is ground!
Special attention:
1, the PC power supply
The so-called power transfer is the input voltage through the pressure circuit to achieve the lift/buck function for the use of other modules, intelligent car production, the input battery voltage of 7.2V, the other modules required voltage as follows: Minimum system board/oled/Eagle Eye camera 3.3V, op amp power supply
I went home today and found my computer couldn't be started.
1. Check.
The Green Line of the power supply is connected to the gray line, and the power supply has no reaction. It is determined that the power supply is faulty.
(Wake
With the popularity of a variety of smartphones, tablets, more and more people find that a variety of digital products, especially the mobile phone itself has been unable to meet the needs of life in the day-to-day use of the time, and the emergence of mobile power can be said to a certain extent to solve the problem. So for those who have not touched the mobile power of consumers, the dazzling range of mob
The actual motherboard maintenance, often beginners in the measurement of the motherboard of the various power supply voltage, easy to be measured in the actual results of the voltage deviation (whether normal), in this brief description, the general motherboard of the main power supply voltage range and common test po
A Lenovo G31T-LM motherboard, CPU core voltage, reset, PG, North Bridge all power supply is not normal, memory voltage 1.4V significantly lower, and later found that North Bridge power supply is the memory of MOS tube power supply
~
1. Digital, analog, and power supply on the Board:
From this figure, we can see that the analog and digital locations are completely separated, and finally each point is connected to the power source, which can prevent the mutual Crosstalk of the ground signal from affecting some sensitive components, as w
The itop-exynos4412 Development Board uses Exynos4412 's main chip, with higher frequency and richer peripherals, with 2GB dual channel configuration DDR3 of memory and 16GB storage, with strong stability, high reliability, can be applied to the performance and processing capacity of higher requirements of embedded system applications. The itop-exynos4412 board has built-in wireless wifi module,Bluetoot
pins on the FPGA are "user Pins" (such as the so-called "ios", or "I/Os", or "user I/Os", or "user IOs", or "io pins", or ... Self-understanding). IO stands for "input-output".Attention:Users can fully customize user Io. They can be programmed as input, output or bidirectional io (three-way buffering). Each "IO Pin" is connected to the IO unit inside the FPGA. This "IO unit" is power-up via the Vccio (IO power
The power ripple index of the DC/DC module is an important parameter. A clean power supply is a prerequisite for the stable operation of the digital circuit and an important guarantee for the parameters of the simulator. To determine the power quality, the Output Ripple of the DC/DC module must be measured. However, th
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.