smc router configuration

CISCO PT Simulation Experiment (14) router configuration for OSPF dynamic routingExperimental Purpose :Mastering the configuration method of OSPF dynamic route selection protocolMastering the OSPF route description in the routing tableFamiliar with the principle and process of routing and packet forwardingExperimental Background : The company connects to the egre

. This information is stored in the FLASH of the router, unless you delete this information yourself, otherwise, the route information remains in the static database. Example 1: the router sends data packets sent to the 0800. cb00.45e9 address from the interface ethernet0. Quidway (config) # bridge address 0800. cb00.45e9 forward ethernet 0 Example 2: delete the route information with the MAC address 0800.

Basic Frame Relay Configuration: Target: Basic Frame Relay Configuration Lab device: Router with serial port) 2 V.35 cable DTE/DCE) 1 pair Tutorial principle: The frame relay standard can be configured and managed permanent virtual circuit PVC in the frame relay network) for addressing, and the frame relay permanent virtual circuit is identified by the data li

CISCO PT Simulation Experiment (12) configuration of router static routesExperimental Purpose : Master the configuration method and application of static routeMastering Route descriptions in the routing tableFamiliar with the principle and process of Routing and Packet forwardingExperimental Background :In addition to the headquarters of a company, there is anot

With the development of wireless technology, wireless routers are becoming more and more popular. So what problems should we be concerned about in its configuration? Here is a detailed introduction. The development of wireless LAN is now very complete, and the speed is getting faster and faster. The current mainstream products not only achieve the speed of common wired Ethernet, but also have basic security assurance. More importantly, no cabling is r

cannot be used directly on the ATM interface or Dialer port; Detailed Configuration Note: During the test, the Headquarters router R3640 is directly connected to AR4640 through the Ethernet port E2/0. AR1830 Branch) Configuration: discur#　sysnameRouter#　ikelocal-namefenbu　#　dialer-rule1ippermit#　ikepeerzongbuexchange-modeaggressive　pre-shared-keyfenbu　

Ppp chap authentication Target: Purpose: Understanding the process and configuration of ppp chap authentication Lab device: Router with serial port) 2 V.35 cable DTE/DCE) 1 pair Tutorial principle: The PPP protocol is located at the data link layer of the OSI Layer-7 model. The PPP protocol is divided into two sub-layers by function: LCP and NCP. LCP is mainly responsible for Link negotiation, establish

Cisco router configuration mode In general, you can configure your router in 5 ways: 1.Console Port connection terminal or running terminal simulation software of the microcomputer; 2.AUX Port Connect modem, connect with remote terminal or computer running terminal simulation software by telephone line; 3. Via the TFTP server on the Ethernet; 4. Adoption of

Packet Tracer 5.0 Experiment (ix) router RIP dynamic routing configurationFirst, the experimental target Master the configuration method of RIP protocol; Master to view the routes generated by RIP learning through dynamic routing protocols; Familiar with the connection mode of WAN cable; Second, the experimental backgroundSuppose that the campus network is connected to the campus netwo

I. Initial Sequence of router startup 　　 When a vro is initialized, The vro performs the following operations: 　　 1) perform power-on self-check from Rom to detect basic operations of CPU, memory, and interface circuit. 　　 2) boot from the ROM and install and download the operating system to the primary storage. 　　 3) if the boot operating system is pre-determined by the boot of the configuration register t

I. Lab Objectives Master the configuration of Integrated routes; View the routes generated by route redistribution; Familiar with Wan cable connection methods; Ii. Lab background Assume that a company connects to the egress router R1 through a layer-3 switch, and router R1 is connected to another router R2. Layer

principle, using a Udpecho request instead of a ICMPECHO request to initiate an attack. While cyber security experts are focused on developing devices that block Dos attacks, they have little effect because Dos attacks exploit the weaknesses of the TCP protocol itself. Properly configured routers can effectively prevent Dos attacks. In Cisco routers, for example, the iOS software in Cisco routers has many features that prevent Dos attacks, securing the rout