Cisco router VLan isolation LAN broadcast packet configuration experiment and summary, ciscovlan
1. Tutorial Description: connect to and set the IP address of the PC according to the network topology. PC1 and PC2 are required to be accessed on VLAN 12, while PC3 and PC4 are accessed on
I. Common technology of Campus networkUnderstand the relevant network component terminology before you begin the following operations.Two. Investigate the school situation and divide the VLAN and IP address segments
VLAN number
VLAN name
IP network Segment
Default Gateway
Description
Switch corresponding port
Lab Environment:650) this.width=650; "alt=" Cisco Packet Tracer three-layer switch interrupt Dhcp-ibm.chick-mingkang.zhou "src=" http://img0.ph.126.net/4fx 93s0ahtpaead19pxmyg==/6619563575538146055.jpg "style=" border:0px;height:auto;margin:0px 10px 0px 0px; "/>Experimental Purpose:1, the VLAN is divided on the three layer switching: vlan10\vlan100\vlan200, and t
Install Cisco Packet Tracer in Linux
What is Cisco Packet tracer?
Cisco Packet Tracer is a powerful network simulation tool used for Cisco authentication training. It provides us with a good interface view for various routers and
What is Cisco Packet tracer?The Cisco Packet Tracer is a powerful network simulation tool for training in Cisco certifications. It gives us a good view of the interfaces of each router and network device, with many options, and we can use unlimited devices in the network just like with physical machines. We can create
port to enable ACL policyNetwork topology1, configure Router 1, turn on the single-arm routing configuration subinterface address and connect the physical interface address of another route and open the port2 Configuring the VLAN of the switch, configuring the port type3 Configuring the IP address of the PC, specifying the gateway4 Configuring router static routing to enable network interoperability5 Creat
Tags: cal enhancement packet share image share access Cisco virtual SRCVLAN, the virtual LAN (Virtul local area network), the VLAN divides the physical connected LAN logic into different virtual networks, its existence can reduce the broadcast domain, enhance the network security and convenient and flexible networking, adding PCs and switchesBy configuring VLANs, you can implement PC1 and PC2 that are conne
) # EndSwitch #% SYS-5-CONFIG_ I: configured from console by the Console
5. View configuration information
Switch # Show running-configBuilding configuration...
Current configuration: 1064 bytes!Version 12.2:No service timestamps log datetime msecNo service timestamps debug datetime msecNo service password-Encryption!Hostname Switch!Enable Password 123456
the VLAN Tag of a user's private packet. the networks at both ends of the user need to access the public network through SwitchA and SwitchB respectively. The VLAN Mapping function must be configured so that the user's private network packets can be transmitted through VLAN planning on the public network. L SwitchA po
policy in Router 2, specifying host and port7 The ACL takes effect under the port of the Router 2 Xia Lian serverNetwork topology1 Configuring Router 1 single-arm routing, establishing sub-interfaces and configuring IP addresses, etc.2 Configuring the Switch's VLAN and port type3 Configuring the IP address of the PC4 Configuring the interface address for Router 25 Configure static routes to communicate properly between networks6 Configure the ACL pol
Tags: color-o switch test one-arm routing access via interface implementation representationTo achieve inter-VLAN communication, in addition to configuring the SVI interface on the switch, you can also implement VLAN data forwarding by configuring sub-interfaces under the physical interface of the router.Configuration ideas:1 The access switch configures the corresponding
) #exit #退出接口配置模式Router (config) #exit # exit Global moderouter#disable# Exit Privileged ModeRouter>Configuring the Router serial interfaceThe serial interface is used to reach the router at the remote site or ISP over a WAN connection.Router>enableRouter#config TRouter (config) #interface serial 2/0Router (config-if) #ip address 192.168.20.100 255.255.255.0Router (config-if) #clock rate 56000# If the DCE cable is connected, set the clock frequency, or skip this step if the DTE cable is connecte
Cisco Packet Tracer Experimental Tutorials
This note is the experimental source of the school computer networks in the course of experimental data, I slightly collated some, in the implementation of the command line to add some comments, implementation is not unique, my implementation is not necessarily optimal, if there is mistake, please correct me;
The following entries directly link to my note-takin
Tags: process proc ima RAC Technology share static term ADOBy configuring static routes, you can achieve an increase in routing entries for routers in a relatively simple network.However, if there are more than 20 routers in a network, it is difficult to configure static routes to accommodate the complexity of routing entries and changes in the network. At this point we can use the RIP protocol to configure simple dynamic routing, thus reducing the workload.Configuration ideas1 Configure the IP
Nat[network address translation] In the absence of IP address in the case of a great use, it can not be normal Sisu network of the intranet address into a legitimate external network address on the public network to send and receive data. At the same time address translation function can also be very good to hide and protect the host network.Nat has static NAT (internal address and external address one-to-one) and dynamic NAT (internal address pool and external address Pool A-do)This time we'll
Tags: div forwards cer packet col out log other CISCBuild a network, the left LAN is 10.0.0.0 network segment, right LAN is 12.0.0.0 network segment, the middle is WAN 11.0.0.0 network segmentThe above success, but not very familiar with, the following again1. First create a network with a visual interface2. It seems that the computer must first connect with the switch to connect with the router3. The rest is very simple, configure the static route is
.
Cisco router in the configuration of ports, or to understand the next few port names and purposes more meaningful, s port is the meaning of serial interface, also known as high-speed asynchronous serial port, is mainly connected to the WAN v.35 cable, commonly said routers and routers when used in connection. F port is a fastethernet interface, called Fast Ethernet port, mainly connected to Ethernet (LAN) used, the popular saying is to connect swit
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.