As we all know, the vswitch ports are both layer-2 interfaces, and these interfaces are connected to physical ports. In a Vlan, these interfaces can be divided into access interfaces and relay ports. If the port of a vswitch uses an access port, it can only belong to a specific Vlan. If the port of a vswitch uses a relay port, it can belong to any Vlan. So when s
I have been learning cisco devices for a while and have never used them in the work environment. I am using a silly switch and adding an FW to the Internet. Considering that the unit is a domain environment, A three-tier switch will be added to the data center next year, and a two-tier switch will be added to the factory. Therefore, a virtual machine will be used to complete VLAN-based experiments in a single-domain environment. This will lay a founda
To configure the schema:Configuration command:Switch>enableSwitch#vlan Database% Warning:it are recommended to configure VLANs from config mode,As VLAN database mode is being deprecated. Please consult userdocumentation for configuring Vtp/vlan in config mode.Switch (VLAN) #vlan
Hands-on practice of Linux VLAN-playing with OpenStack (13) every five minutes)
This section describes how to implement and configure the following VLAN network in the experiment environment. Configure VLAN
Edit/etc/network/interfaces and configure eth0.10, brvlan10, eth0.20, and brvlan20.Vmdiff is used to demonstrate modifications to/etc/network/interfaces.
Three-layer switching technology is two-layer switching technology and three-layer routing forwarding technology, the traditional exchange technology in the data link layer to operate, three-layer switching technology is the network layer to implement high-speed packet forwarding. The third layer switching technology can realize the function of network routing, and the optimal network performance according to different network conditions. The most important purpose of the three-tier switch is to
Php string replacement, segmentation and connection methods, php string replacement and segmentation. Php string replacement, segmentation, and connection methods. php string replacement and segmentation this article describes how to replace, split, and connect php strings. For your reference, such as replacing, splitt
Segmentation GBK Chinese garbled problem solved, segmentation GBK Chinese garbled
Recently encountered a magical word "Mingtao (TAO)".
The specific process is this:
1 $list Explode (' | ', ' ABC Mingtao |BC '); 2 Var_dump ($list);
Get the result of this partition.
Unlike imagination, the result is this:
Array (3) { [0]=> string(4) "ABC? [1]=> "" [2]=> "BC"}
There was garbled, and inexplicably appeare
Huawei vlan division, single-arm routing and Static RoutingHuawei vlan division, single-arm routing, and Static Routing allow all members to access the InternetHuawei topology: IP address planning! Assign IP addresses to three computersVLAN Division:[Huawei] un in en close message center[Huawei] Change the switch name in sysname SW1[SW1] inter vlan 1 enters the s
We know that the traditional LAN Ethernet adopts the CSMA/CD method with conflict detection. In the CSMA/CD network, nodes can use the network whenever they have data to be sent. Before a node transmits data, it performs a "listener" to check whether the network is busy. If not, the node starts to transmit data. If the network is in use, the node waits. If the two nodes do not hear anything and start to use the line at the same time, a conflict will occur. When sending data, if it uses a broadca
We all know that DHCP is a service for IP address management. In some network changes, we also need to modify the settings. Here we will explain how to configure the multi-vlan dhcp service. All aspects must be taken into account when upgrading the network, and how to implement the DHCP service in a multi-VLAN environment is one of them.
Multi-vlan dhcp service s
Database vertical segmentation, HORIZONTAL segmentation
I have found that share:
Sometimes partitioning a table can improve performance. There are two ways to split a table:1 Horizontal segmentation: Place data rows into two separate tables based on the values of one or more columns of data.Horizontal splits are usually used in the following situations.The tabl
The actual example of a VLAN configuration is very simple, just like the eth-switch routing method through VLAN. First, let's look at a method with high hardware efficiency: Port1 ~ 4 As the access port and the user mode on the hardware, that is, the packets sent from the PC to these ports do not carry VLAN-tag. After the SW hardware receives the packets, based o
Fix after "Go" testSuccessfully let IVM run a number of VLANs, add a can carry multiple Vlanid network card, Nativevlan is the compromise method of transformation, if not like this method, with---Delete multi-vlan Nic method, in general, Lpar can only and IVM in the same network segment, I have a study, Success has allowed IVM to run multiple VLANs. The steps are as follows: first, change the blade's built-in switch settings to find the appropriate in
This document introduces how to divide 802.1Q VLANs based on examples.Example: as shown in the preceding figure, the marketing department and product department of a company set up network isolation. The two departments can access the Internet and servers of their respective departments, but mutual access between departments and servers of other departments is prohibited.In this example, the actual topology and port connection effect are as follows. This article describes how to divide VLANs bas
Because VLAN technology is closely related to LAN technology, we should first understand the knowledge of LAN before introducing VLAN.
LAN) is usually defined as a separate broadcast domain, mainly using the Hub, bridge, or switch and other network devices to connect to all nodes in the same network segment. The network nodes in the same LAN can communicate directly without a network router. The communicati
Experiment topology:
"Color: #000000"> tutorial Environment Description:1. Use routers R1 and R2 to simulate a PC and disable its routing function;2. Set the IP address of port fa0/0 of router R1 to 192.168.1.2/24, and the default gateway to 192.168.1.1;3. Set the IP address of port fa0/0 of router R2 to 192.168.0.2/24, and the default gateway to 192.168.0.1;4. Disable the routing function of switch SW1 as a layer-2 switch, and divide two VLANs, vlan14 and vlan15;5. Add port fa1/14 of switch S
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.