10gb nic

Linux host original network card ETH0,IP for 172.19.74.X/24, add a network card eth1, configure another network segment of the IP 10.219.17.x/24, found their respective to the gateway, but the original 172.19.74.X segment of the host can not access the host.650) this.width=650; "src=" http://s2.51cto.com/wyfs02/M01/7D/06/wKioL1beoAKRdhoyAAL1yYrZRoU831.jpg "title=" 12.jpg "alt=" Wkiol1beoakrdhoyaal1yyrzrou831.jpg "/>Viewing the routing table discovery, the default route goes to the new

1. View Vi/etc/udev/rules.d/70-persistent-net.rulesHere can see your network card information, find your corresponding network card nameFor example (this is the virtual machine where I add a new NIC that does not show its profile) # PCI Device 0x8086:0x100f (e1000)subsystem== "NET", action== "Add", drivers== "? *", attr{address}== "00:0c:29:52:5c:06", attr{type}== "1", kernel== "eth*" , name= "Eth0"# PCI Device 0x8086:0x100f (e1000)subsystem== "NET",

1. Get IP address automaticallyVirtual machines use bridging mode, which is equivalent to a network connected to a physical machine, and the physical machine network has a DHCP server that automatically assigns IP addresses.#dhclient Auto Get IP address command#ifconfig Query System network card information, IP address, MAC addressAfter assigning to an IP address, ping the IP address with the physical machine and detect if it is ping.2. Manually set the IP addressIf the virtual machine does not

Today in the practice of a sudden thought if the current use of the virtual machine in the system is broken or an unknown failure to affect the learning progress what to do, after all, re-install a system to delay a lot of time, so want to use the current normal system copy a backupAfter copy, use VMware to open and change the name, boot OK, login OK, test network faile ... Restart the NICTip "Device eth0 does not seem to be present,delaying initialization"Think carefully, clone backup ... Oh, t

First, installed under UbuntuThis does not have to be installed, the system is well supported.System->administration->hardware DriversChoose the Broadcom STA wireless driverActivateIf you do not have this option, execute it in the shell:sudo apt-get updatesudo apt-get--reinstall install bcmwl-kernel-sourceAfter restarting, repeat the previous step to activate the driver. I tested the Chinese version of Ubuntu14.04 and found that this driver was not installed by default, and repeated the above co

1. Create the Bond0 file:#vim/etc/sysconfig/network/ifcfg-Bond0bootproto='Static'Broadcast="'ipaddr='192.168.74.141/24'NETMASK='255.255.255.0'NETWORK="'STARTMODE='Auto'Bonding_master='Yes'Bonding_slave0='eth0'bonding_slave1='eth1'bonding_module_opts='mode=1 miimon=100 fail_over_mac=1'ethtool_options="'MTU="'NAME="'remote_ipaddr="'USERCONTROL='No'Explanation of Interpretation:Mode 0 is expressed as load balancing mode, both NICs work (requires switch port aggregation, test failed on SLEs 12SP3 wi

ifconfig See the IP is not the IP I want, and the first NIC display is also eth1, which is obviously problematic,Vim/etc/sysconfig/network-script/ifcfg-eth0 See the IP is I set the IP, but the Mac is wrong, see and Ifconfig inside the eth1 is not the same,Then Vim/etc/udev/rules.d/70-persistent-net.rules see is a eth0 and a eth1, which is obviously wrong, I only have a network card, Eth1 mac and Ifconfig see is the same,0,vim/etc/udev/rules.d/70-persi

Errors0Dropped0Overruns0Carrier0Collisions0Lo:flags= the65536inet127.0.0.1Netmask255.0.0.0Inet6::1Prefixlen -ScopeID0x10Loop Txqueuelen1(Local Loopback) RX packets -bytes1392(1.3KiB) RX Errors0Dropped0Overruns0Frame0TX Packets -bytes1392(1.3KiB) TX Errors0Dropped0Overruns0Carrier0Collisions0Several key parameters in the above code illustrate:inet 192.168.38.138 This is the IP address of the NIC Ens33Netmask 255.255.255.0 This is a subnet maskDhclient

1. Edit the file/etc/sysconfig/networkAdd a line inside:Vlan=yes2. The configuration file ifcfg-eth1.10 and ifcfg-eth1.240 that are regenerated into the NIC deviceCd/etc/sysconfig/network-scriptsCP Ifcfg-eth1 ifcfg-eth1.10CP Ifcfg-eth1 ifcfg-eth1.2403. editing files ifcfg-eth1.10 and ifcfg-eth1.240The syntax that resembles writing ifcfg-eth1 in it is matching this server's IP address, netmask, network, and so on 192.168.10 network segment and 192.168.

bond0 Span style= "font-family: ' The song Body '; > ip ! If you have already turned on network properties to view the NIC information, press exit. Do not click OK, otherwise you will modify eth0 and eth1 configuration information, so bond0 failure. 2 uninstall bond0 device #rm-f/etc/sysconfig/network-scripts/ifcfg-bond0#vi/etc/etc/modules.confThen delete the following two lines after saving the exitAlias Bond0 BondingOptions Bo

NIC binding mode altogether has seven kinds (0~6) bond0, Bond1, Bond2, Bond3, Bond4, Bond5, Bond6 There are three kinds of commonly used Mode=0: Balance load mode, there is automatic backup, but need "Switch" support and settings. Mode=1: Automatic standby mode, if one line is disconnected, the other lines will be automatically prepared for assistance. MODE=6: Balanced load mode, there is automatic backup, do not need to "Switch" support and setti

The computer network card can not get the IP address of such problems, you may try to change the network card working mode to solve. Expand network adapters in Device Manager, double-click the NIC driver flag, and then switch to the advanced option to change the NIC operating rate mode from automatic mode to 10Mbps Full-duplex mode in the properties. If you still do not solve the problem, it is likely that

　　Analysis: The main---connected to the external network of computers, has two network card (WinXP system) 　　From---Computers that need to connect to the main computer (Win7 system) Network card 1---The main computer connected to the external network network card Network Card 2---The main computer needs to connect the network card from the computer Nic 3---from the computer network card 　　The first step: Please make sure that a network card of th

Since the desktop is plugged into the Ubuntu14.04 after installing the rear lights, it cannot use a wired network.Find data found the original network card driver problem, the solution is as follows:1. Check the NIC driver nameLspci-vFind the Ethernet connection kernel drive in use:r81692. View specific versions of r8169Modinfo r8169 View is not the latest version, not the words may be the version is too old3. Uninstall the original drivesudo rmmod r8

Tags: Linux network card eth1 How to change to eth0Normally, the first time that Linux recognizes a NIC is eth0, and the second one is eth1. Sometimes we use the virtual machine cloning technology after the network card information will change, the newly cloned virtual host network card name may become eth1. No matter how we modify it, this is a problem when we use N virtual machines for ha-heartbeat experiments.In this case it is because the replicat

Delete User Default profileDue to the default emptying, the configuration file is the system automatically generated user device profile saved under/etc/udev/rule.d/:# Cp/etc/udev/rule.d/etc/udev/rule.d.bak.0-r# rm/etc/udev/rule.d/*Modify the NIC configuration file to add multiple IP configurations#vim/etc/network/interfacesModify or add the following:Auto Lo iface lo inet loopback auto eth0 iface eth0 inet static address192.168.76.192netmask255.255.2

First, the Linux virtual machine cloning, the boot system found that the network card could not start, and then ifup eth0 network card will prompt (Device eth0 does not seem to be present, delaying initialization.) failed.Second, the treatment method:Method One:1, [[email protected] ~]# Vim/etc/udev/rules.d/70-persistent-net.rules# This file is automatically generated by the/lib/udev/write_net_rules# program, run by the Persistent-net-generator.rules rules file.## can modify it, as long as you k

objWMIService = GetObject ("winmgmts:\\" StrComputer "\root\cimv2") Set colitems = objWMIService.ExecQuery ("select * from Win32_NetworkAdapterConfiguration where ipenabled=true", 48) For each objitem in colitems msg = MSG "No.:" Objitem.index "MAC:" objitem.macaddress VbCrLf "Nic:" Objitem. Description VbCrLf VbCrLf Next IDX = InputBox (msg, "1/2 Please enter the number of the Mac you want to modify", "1") If not IsNumeric (idx) Or Len (

I have a comparison of old cow pulled a car desktop computer, is 3 years ago 1000来 block money back to students. Recently moved to find after the boot crazy black screen. Helpless, the big rectification today. First thought is the graphics interface loose, removed the reload, still black screen ... Then think that the graphics driver is damaged, reload, still ... Then think that the system is too old (installed XP), reload, still ... Then installed an Ubuntu, not black screen, but the spee

Tags: centos virtualbox nat Nic Link-flapThese days, when running CentOS on the VM box, there is a sudden abnormal regular network card, normal use of 1, 2 minutes and turn off the reset and normal repetition of the phenomenon,Looking at this phenomenon, recall several actions that may be relevant before a phenomenon occurs:1 Upgrading the CentOS kernel with Yum Update: tested and kernel-independent2 suspected of large volume of communication data ins