2 petabyte hard drive

1, keep the computer working environment clean Hard disk with Ultra fine filter paper of the breathing hole with the outside world, it can be used in the ordinary no purification device indoor environment, if the dust in a serious environment, will be adsorbed to the PCBA surface, spindle motor internal and plug the breathing filter, it must be dust-proof. There is also a humid environment, voltage instability can lead to

Computer hard drive does not read the disk can not boot solution: 1, after the boot system did not find or can not identify the hard drive This kind of situation causes the computer not to be able to boot from the hard disk, even if we use other means to start the computer

　　 The steps are as follows: 　　First, if you have the following symptoms of the hard drive, you should pay attention to the hard drive has been a bad way: (1) Read a file or run a program, the hard disk repeatedly read the disk and error, prompting file damage information,

notebook does not recognize the new hard drive what to do The notebook does not recognize the new hard drive solution one: 1. After the power on the hard drive no response When the power is turned on and the laptop is started,

computer does not read hard drive how to solve Computer does not read the hard drive the reason and the solution one: The hard drive is not detected by the computer. 1, in fact, can not detect the

1, the system does not recognize the hard drive This type of failure is more common, that is, from the hard disk can not start, starting from a disk can not enter the C disk, the use of the CMOS automatic monitoring function can not find the existence of the hard disk. Most of this fault occurs in the connection cable

. Raid: A disk array (default value) can be created for the hard disk on the SATA port of the motherboard ). You only need to adjust the priority of the serial and parallel ports according to the actual situation to use the SATA hard disk normally. (From the options above we can see that here the S-ATA hard drive can

MB, which is enough to be final! No matter how big your hard disk is, that's enough! After you have installed the system, check it out. In fact, it takes 45-50 m.) Tips: BOOT mount points are not required. However, I personally suggest that if you want to create a dual-system, you 'd better separate it. When you install the grub boot, install it on the boot, that is, the dual-system, the purpose is to be clearer and more convenient.

C8005H address. The specific operation is as follows:A: \> Debug-G C800: 0005 (// the information displayed on the screen (different BIOS versions may display different information). Press enter to prompt :)Current Interleave is 3 select new interleave or Return for current (// This requires the user to select a cross factor, press enter to take the default value 3, you can also enter a new cross factor value, generally, the cross factor of the hard

you a swap every day. Dell also has a number of software services, such as remote management cards, which are also very good to use. ” As the cool disk founder Guzhi said, servers, storage and switches, and even hard disk network equipment is not once and for all, regardless of how manufacturers promise to reworks the product before the low, or even 0 fault guarantee, but the after-sale problem still deserves attention. Therefore, in order to avoid

no image display, only the sound of fan rotation. Another reason is that the compatibility of the newly added hardware is not good enough to cause the above situation to occur. 2.BIOS Settings Change When the BIOS setup error, such as the memory of the read and write parameters set incorrectly, the hard drive mode settings, the onboard sound card and integrat

computers often do not detect the hard drive what to do The computer often does not detect the hard drive solution one: There are several reasons for these: 1, the hard disk itself has a problem, may be broken, with tools to detect, bad can only send repair.

computer does not recognize the mobile hard drive what to do Under normal circumstances, a removable hard disk is connected to a host and the system can recognize it as a removable storage device and automatically add a letter to my computer. If the system will recognize the mobile hard

Jumper (English jumper) is a small switch that controls the current flow on the circuit board. Its role is to adjust the equipment on the different electrical signals of the relationship, and to adjust the operation of the equipment, such as the motherboard voltage, drive master-slave relationship and so on. The jumper is basically composed of two parts, partly fixed on the motherboard, hard drives and othe

the computer. You fumble through all the cables, reseat the connectors, and even change the wires. The hard drive still doesn't move. Call customer support, it's time to announce surrender and call the Customer Support department. First try asking your computer vendor, or the hard drive manufacturer's technician. Mayb

With the sharing of files more and more, movies, picture games and other large-capacity data selected by the mobile hard disk as a storage carrier. Many netizens reflect, when they buy the mobile hard disk put on the computer, the system will be mobile hard disk recognized as "Unknown USB device", the mobile hard disk

, resulting in the mobile hard drive can not be recognized by the system. Fortunately, the mobile hard disk box dedicated USB cable on most of a PS/2 connector, as long as the connector plug in the motherboard PS/2 interface can be. Third, improper operation caused the mobi

What to do if a mobile hard drive can't be identified by computer Solutions for mobile hard drives that cannot be identified by the computer: Method One: System-related Setup problems 1, do not think that as long as the motherboard has a USB interface can use the mobile hard disk, but also depends on whether the sys

driver 2. Questions and Answers 2.1. Which commands can be received by the hard drive. What kind of processing results. Hard drives can accept many commands (both hardware-defined and system-independent). Here, we use the IDENTIFY Device command, explained below: Reference manual: At Attachment with packet Interface d

not see the difference! Because use is the factory technology to repair, factory technician also may not see the difference lies! A Pentium4 machine, the use of 80GB hard drive, start Windows XP system, has been stuck in the start screen, hard drive constantly "ka" rang, apparently