4g load balancing router

, you only need to add: Iptables-I RH-Firewall-1-INPUT-d 224.0.0.18-j ACCEPT 2. If you use a script to configure a firewall, add the following rules: Iptables-a output-o eth0-d 224.0.0.18-j ACCEPT iptables-a output-o eth0-s ACCEPT-j ACCEPT iptables-a input-I eth0-d 224.0.0.18-j ACCEPT iptables -a input-I eth0-s 224.0.0.18-j ACCEPT 5. Summary Keepalived implements dual-machine Hot Standby through virtual routing, which is superior to other solutions. Because it is a fixed master-slave Hot

1. when multiple paths exist at the destination, and the metric values of multiple paths are the same, the equivalent load balancing can be performed, 650) this. width = 650; "src = ".. /attachment/201210/171627301 .jpg" border = "0" alt = "" data-pinit = "registered"/> after completing the configuration, view the neighbor table, topology table, and route table a on R1. neighbors table 650) this. width = 65

-slave mode is used for data synchronization. Sqlrelay solves connection pool problems and implements Load Balancing for read/write splitting. Sqlrelay is configured with three instances A/B/C. A is responsible for reading data from Master and slave, B is responsible for writing data, and only writes data to Master. C is the router and is responsible for applicat

Keepalived + HAProxy implements the configuration of MySQL high-availability load balancing, keepalivedhaproxy Keepalived Because mysqlcluster is used in the production environment, high-availability load balancing is required. keepalived + haproxy is provided here. Keepalived is mainly used to implement fault isolatio

on the Web server. (1) The upstream command of the scheduling algorithm nginx is used to specify the backend servers used by proxy_pass and fastcgi_pass, that is, the reverse proxy function of nginx, therefore, the two can be combined to achieve load balancing, while nginx also supports multiple scheduling algorithms: 1. Round Robin (default) each request is distributed to different backend servers one by

succeed. When the above content is set up, open the management tool--Network Load Balancing Right-click on Network Load Balancing cluster-connect to existing Enter a 192.168.0.100 Click Connection at the host If the above interface appears, the connection succeeds ~ if Computer B on Computer A is unable to co

LVS Cluster has DR, TUN, Nat three configuration mode, can be the WWW service, FTP services, mail services, such as load balancing, the following through the establishment of the WWW service load Balancing example, the DR mode based on the LVS cluster configuration. I. Configuration of the Director server There are t

Keepalived+lvs+nginx High Load Balancing availableThe previous article written the Nginx load balancer, this article realizes the high Availability (HA). The overall design of the system is to use Nginx to do load balancing, if there is an nginx single-machine failure, the w

HAProxy load balancing, 1. HAProxy introduction: HAProxy is a free, efficient, and reliable high-availability and load balancing solution. This software is ideal for processing layer-7 data requests from high-load sites, HAProxy's working mode enables it to be easily and sec

server, port ing is required on both public lines to serve the Internet user groups on different lines. Iii. Solution 1. Add a link load balancing device in the solution, connect the network cables connected to the WAN port and WAN1 port of the VPN device to the link Load Balancing Device. The line of the WAN2 port on

Alteon is used in the use of dual-machine master and Standby mode of work, the corresponding group network according to different ways are divided into a direct-connected group network, single-arm network of two pairs of networks and triangular transmission network, the following in turn, detailed introduction. 1.1Direct Connect NetworkingThe network topology diagram is as follows: ( Standard Architecture )650) this.width=650; "Src=" Http://s1.51cto.com/wyfs02/M00/87/07/wKioL1fSB7XDvLC9AAEq9X4j7

-slave lvs and the master lvs is damaged, transfer the IP address and lvs to the backup lvs. Its high availability is mainly based on the VRRP protocol. VRRP is an "election" protocol that dynamically assigns the responsibility of a vro to other routers in the same VRRP group, this eliminates single point of failure in static routing configuration. If a VRRP device uses the virtual router IP address as the real interface address, the device is called

tunneling mechanism implementation. (1) RIP, DIP, VIP are public network address;(2) The Gateway of the RS cannot point to the DIP;(3) The request message must be dispatched by the director, but the response message must not pass through the director;(4) port mappings are not supported;(5) the OS of RS must support tunnel function;2,DR mode working principle:1, receives the client request, chooses one realserver IP according to the set load equalizat

Recently the team is ready to refactor the project, using RABBITMQ and several scenarios, with a focus on the upcoming scenario in the project. About RABBITMQ is not here detailed explanation, the specific view RABBITMQ Chinese manual. See the architecture diagram directly:650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M01/6F/65/wKioL1WbU4KDmHxsAAEkMsBP5vA283.jpg "title=" RABBITMQ high-availability load Ba