access home network with vpn

Generally, the company uses VE1260, the branch uses VE982, and the Intranet uses a layer-3 switch, which divides VLAN, and establishes a pptp vpn between VE1260 and VE982. After the branch transfers the Intranet VPN to the company, you can access all the CIDR blocks of the company's internal network, including other CI

by default, you can find the "guest" account in "Control Panel | Administrative Tools | Computer Management | local users and groups | users", and right-click the account to open the "guest properties" dialog box, remove the check mark on the "Account Disabled" check box. After exiting, you can access Win2000/XP from Win98.In fact, after the Guest account is enabled, the biggest benefit is that you do not need to enter the user name and password when

NAP is a Windows mechanism that ensures that only computers that meet security requirements allow access to the network. Using NAP can make the network more secure. Unfortunately, when Microsoft launched this mechanism for the first time, NAP only checked some configuration settings and was difficult to execute. However, the NAP has been improved, and Windows Vis

processing capability may cause bottlenecks and the network speed may also be affected (after all, an ADSL cannot connect too many clients ). Generally, it is recommended that the number of connected clients be less than 100 to 70 ~ 80 is the best configuration. This not only ensures that the access speed of Internet cafes is not affected, but also makes full use of resources to save money. Remedy the "

At home, company seats, company meeting room, company corner, customer site, hotel... you have to configure your network card to ensure that it is consistent with the configuration of the location. This is too annoying! Is there a way to avoid this tedious configuration? In this backward and self-sufficient DIY age, the answer is no doubt certain for the tillers in the male and female workshops!Sggw module

networked in star mode. If the number of existing pipe holes is insufficient, the number of users is concentrated in the scope of this Council. In urban planning areas, the combination of ring and bus networks should be prioritized. 6. Core configuration principles1) sink nodeFor a star network, the number of 6-core optical fiber cables under each sink node decreases step by step from the trunk to the branch. For the combination of ring and bus netwo

can provide users with 2.4 k, 4.8 k, 9.6 k, 19.2 k, N * 64 (N = 1 ~ 31) and 2048kbps speed of the fully transparent dedicated circuit DDN user terminal can be asynchronous terminal (DTE), computer (PC) or local area network. Features: 1. Digital Circuits are used, with high transmission quality and low latency. The communication rate can be set between 2.4kbps2048kbps as needed. 2. The circuit adopts transparent transmission and can be automatically

Broadband access to the network that is, users can directly connect to the Internet on a broadband network, can also extend the Internet platform to the community (or hotels), that is, combined with the needs of the region and the characteristics of the Internet access and application platform in the user's relatively

high density and need to provide comprehensive narrowband and broadband services. both the FTTO and FTTH structures are equipped with a non-source optical splitter on the side of the road, and The ONU is moved to the user's office or home, which is a truly transparent optical fiber network. they are not subject to any transmission standard, bandwidth, wavelength and transmission technology, and are the ide

mechanisms, NSR, and other advanced features. 2. Comprehensive business support capabilities ZXR10M6000 provides a wide range of MPLSVPN functions and VPN tunneling functions such as IPSec, GRE, and L2TP. The IPSec tunneling technology is a basic technology to ensure IP Security, by configuring the same policy between peer entities, a secure IP packet transmission channel is established. The GRE tunnel technology encapsulates the datagram of some

the NAC solution include: 1. It helps ensure that all network devices of users comply with security policies, greatly improving network security and avoiding the impact of scale and complexity. By actively defending against worms, viruses, spyware, and malware attacks, organizations can focus on active defense (rather than passive response ). 2. Extend the value of existing CISCO networks and anti-virus, s

-WLL system working frequency band for 1785--1805mhz, duplex mode for TDD, multiple access mode for CDMA+SDMA, modulation mode for DQPSK, this system should be the attention of the people in the domestic industry." (☆ Introduction to Programming Network ☆)6, based on cordless telephone technologyBased on cordless telephone technology, the wireless access

area, in the installation box of the building, configure the number of fiber cores according to the quantity of ONU3346 configured for the building, and configure two fiber cores for each ONU3346 (1 core for main use and 1 core for backup ). For multi-building buildings, two buildings share one ONU3346, fiber optic to building 1, and Class 5 lines in Building 2 are directly delivered through pipe. 4. ONU Deployment SchemeIn the initial stage of this work, the goal is to provide customers with d

Currently, the access network technology is widely used. Many people may not understand the technical features and practical applications of the access network. It does not matter. After reading this article, you will certainly have a lot of GAINS. I hope this article will teach you more. Computer

, LAN and other access technology, combined with SDH/ATM/IP network technology, the B-nod placed into the building and intelligent wiring system, to provide users with convenient broadband access.(2) Small and medium-sized enterprisesSBI strategy--according to its demand characteristics, B-nod uses ADSL, DDN, n*64kbit/s, 64kbit/s and other data interfaces.(3) Chu

=" "height=" 393 "border=" 0 "hspace=" 0 "vspace=" 0 "style=" width:700px;height:393px; "alt=" Wkiol1depm6i9p-waaneqesojok721.png "/>24, click LAN interface-Add, set interface name INSIDE,IP address 10.10.10.10, netmask 255.255.255.0, the rest of the default does not change.650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M00/80/E7/wKioL1dEPyDShfr5AANG5QwqHmI336.png "title=" 41.png "Width=" "height=" 393 "border=" 0 "hspace=" 0 "vspace=" 0 "style=" width:700px;height:393px; "alt=" Wkiol1de

solutions. Solution 1: LAN/ATM route access This scheme requires an ADSLModemADSL router that integrates the routing function ). BAS is deployed on the carrier's backbone network and is responsible for IPv4 and IPv6 broadband access networks. Create an ATMPVC between the BAS and the ADSL Router. Both IPv4 and IPv6 can be transmitted through the same PVC in RFC14

Wireless Access networks are currently the mainstream access technology. Generally, small enterprises still have strict design solutions for wireless access networks, especially in terms of cost and maintenance, at the same time, pay attention to the complexity, which is very important. Trend of ADSL + WLAN Because it provides nearly 100 times faster than the 56