Hard Disk interfaces include four types: IDE, SATA, SCSI, and fiber channel.
IDE
IDE is called "integrated drive electronics" in English, that is, "Integrated drive electronics ". It is intended to be a hard drive that integrates the "hard disk controller" with the "disk body. The integration of the disk and controller reduces the number and length of cables on the hard disk interface, enhances the reliability of data transmission, and makes it easi
SASAndSATAHard Disk differences
As you know, like ata, SCSI is a parallel technology that can connect multiple devices through their respective data channels. Like ata, SCSI is also evolving towards Serial technology, which is SAS (Serial Attached SCSI ).In short, SAS is a new generation of SCSI, which includes some im
As one of the most important devices in the storage system, fiber channel switches are widely used. I believe many consumers do not know how to buy them, the following is a detailed analysis of the selection of fiber channel switches. The fiber channel network built through the fiber channel (FC) switch is called Fabric or the fiber channel network architecture.
Similar to Ethernet switches, FC switches are usually tightly integrated into the system when most users build storage. On the one hand
many other steps to consider, but any hardware solution that includes upgrading or purchasing new devices may be expensive.
3. upgrade from IDE To SCSI
If your hard disk is an IDE drive, you can upgrade it to the SCSI drive for better overall performance. Because the IDE controller must access the CPU, CPU and disk-intensive operations may become very slow. The SCSI
Experimental environment: Virtual machine: VirtualBox 5.0.24 r108355 operating system: rhel-server-6.5-x86_64
Saw the Liu Xiang soldier Big:
use Udev on Linux 6 to troubleshoot RAC ASM storage device name ProblemsI operated a, previously in the linux5 when I was using asmlib to bind ASM, reference to think twice, I am in the creation of virtual hard disk in the SCSI format of the hard drive, in the Linux 5 when there is no problem, but I am in Linux
device control software unreasonable settings are likely to cause the bus set class failure. In addition, some bus controllers themselves in the installation of the use of some of the correct settings to be used well, such as the IDE device master-slave disk problem, SCSI device ID number problem and so on. 5, Bus equipment failure bus and bus devices are always indispensable, and this derived from the bus equipment class fault is definitely stra
I. Environment Description RHEL 6.6 + Oracle 11.2.0.4 storage replacement, need to add a new disk, replace the old storage disk, the following is the test steps. II. test process [[[emailprotected] ~]# cd/etc/udev[[emailprotected] udev]# lsmakedev.d rules.d udev.conf[[email protected] udev]# CD rules.d/[[emailprotected] rules.d]# ls55-usm.rules 60-pcmcia.rules 70- Persistent-net.rules 98-kexec.rules60-fprint-autosuspend.rules 60-raw.rules 90-alsa.rules 99- Oracle-asmdevices.rules60-openct.rules
+ repair-know-net (w_ww*dnw_xzs*co_m)
(2) Eide interface
The Eide interface is much better than the IDE interface and is currently the most popular interface. First, the peripherals it supports are no longer 2 but 4, supported devices in addition to the hard disk, including CD-ROM drive disk backup devices, and so on. Second, the Eide standard cancels the 528MB limit and replaces it with the 8GP limit. Third, the Eide has a higher data transfer rate and supports PIO Mode 3 and Mode 4 standard
register * @ sht: template for SCSI host * Register initialized ata host. @ host is allocated using * ata_host_alloc () and fully initialized by LLD. this function * starts ports, registers @ host with ATA and SCSI layers and * probe registered devices. * locking: * inherited from calling layer (may sleep ). * returns: * 0 on success,-errno otherwise. */ int ata_host_register (struct ata_host * H
1: Due to work, I have been engaged in the development of 2 * 36port Expander in LSI for the past few months. It mainly parses and processes the SSP, SMP, and SES command protocols in SAS.
The SDK of LSI uses the threadx operating system. The kernel of its chip is ARM920T, which provides the SAS protocol processing function at 920t. I personally feel that the Code style is not good.
My personal understanding of expander is as follows:
The lsisas2x36 is a 36-port, 6.0-Gbit/s Serial Attached
. It is a device file, more specifically, it is a device node. This node is created using the mknod command, which specifies the master device number and secondary device number. The primary device number indicates a certain type of device, which generally corresponds to a specific driver. The secondary device number generally distinguishes different attributes, such as different usage methods, locations, and operations. This device number is obtained from the/proc/devices file. Therefore, the d
after high frequency, the function of opening an error significantly reduces the chance of errors. However, the error correction is performed at the cost of system performance, and some CPUs with higher performance will become worse if the function is turned on. It seems that stability and speed cannot be both done. It depends on how you think about it.5. Quick power on self test (quick self-check)With this option enabled, the system will ignore some BIOS self-recommended processes to make the
ISCSI technology is a SCSI instruction set that is developed by IBM and used by hardware devices to run on the upper layer of the IP protocol, this command set allows you to run the SCSI protocol on an IP network so that it can select routes on high-speed Gigabit Ethernet. The biggest benefit of iSCSI is that it can provide a fast network environment. Although there are still some gaps between its performan
A little Linux every day-hard disk knowledge today, disk interfaces are mainly divided into two types: IDE (IntegratedDriveElectronics), SCSI (SmallComputerSystemInterface ). They each have some differentiation or evolution, so the technical terms on disk interfaces...
A little Linux every day-hard disk knowledge today, disk interfaces are mainly divided into two types: IDE (Integrated Drive Electronics), SCSI
hba, transmission ISCSI protocol, Interface type is the same as that of Ethernet card. ISCSI (internet SCSI) is a set of commands that define the transmission of SCSI protocols over TCP/IP networks. He expanded the initiator and target defined by SCSI from the original SCSI bus connection to the internet, breaking the
1.11 SAN storage technology:Network Connections from storage to hosts have a variety of mechanisms, including DAS, SAN, and NAS. For large applications, key applications often adopt the SAN Storage Architecture, which has the advantages of high performance, it is easy to expand, but the disadvantage is that the management is complicated and expensive (especially the FC optical network ).
For example, key services such as web servers and database servers are connected to the optical fiber switch
program partitions that do not change frequently like/usr, but it can create a miracle in the/home partition of a multi-user system. It takes the same time as the disk fragmentation of the Windows NT Server.
If the disk performance is still unsatisfactory, there are many other steps to consider, but any hardware solution that includes upgrading or purchasing new devices may be expensive.
Upgrade from IDE To SCSI
If your hard disk is an IDE drive, yo
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.